×
Quick Used Equipment Filter












used search tag

See All Locations

TS 4X2 UTILITY VEHICLE

Traditional Utility Vehicle

  • Best in class work capability
  • Enhanced stability for better performance in difficult terrain
  • Best in class durability
  • Freight not included in list price
Starting At:$7,649.00
Test Drive
View Product Brochure



Features



Gator™ TS 4X2/Gator TX 4X2 Gator™ TS 4X2/Gator TX 4X2

Power is transmitted from the engine, through a continuously variable clutch system, to a transaxle. Power is transmitted from the transaxle directly to the rear axle.

 

Key elements of the drive system are as follows:

Variable-speed drive

 

The variable-speed drive consists of two clutches connected by a drive belt:

  • Drive clutch is attached to and rotated by the engine.
  • Driven clutch is attached to and drives the transaxle.

Features include:

  • Infinite selection of speeds (0 km/h to 32 km/h [0 mph to 20 mph])
  • No shifting necessary as operator increases speed
  • Adjusts speed to the load to avoid bogging down when going up a hill or through challenging conditions because the wrong gear was selected
Variable-speed drive Variable-speed drive

How the variable-speed drive works:

  1. As the engine speed increases, the spring-loaded drive clutch is closed by weights being forced out by centrifugal force.
  2. As the drive clutch closes, the belt rides up to the largest diameter of the drive clutch and forces open the driven clutch.
  3. With the belt running in the smallest diameter of the driven clutch, the speed being transferred to the transaxle is increased.
  4. The driven clutch is designed to sense varying loads (inclines, mud, etc.) and constantly adjusts the drive speed upward or downward, so the engine rpm remains constant at constant throttle position.

Transaxle

 

The transaxle is fully enclosed and runs in oil for reliability.

 

Helical gears are used for quiet operation.

 

Differential design reduces scuffing of the turf during turns because the inside wheels turn slower than the outside wheels (vehicles that have a solid axle shaft must skid the inside wheel when making a turn).

 

Traction assist (differential lock) is built into the transaxle:

  • Allows locking the rear drive wheels together
  • Provides increased traction in tough spots

A neutral start safety interlock is provided for the engine ignition system.

Heavy-duty rear axle housings

 

Gator TS 4X2

Bolt-on cast-aluminum rear-axle housings provide an extremely strong supporting structure.

  • Large, sealed bearings are located inside the housing for better protection
  • Forged-splined shaft for increased torsional strength

Gator TX 4X2

One-piece forged axles are splined for maximum strength.

  • Large, sealed bearings for better protection and load-carrying capabilities
  • Forged-splined shaft for increased torsional strength
  • Nodular cast-iron housing for increased durability

 

NOTE: The TS 4X2 is not sold in Australia/New Zealand.

Side-by-side bucket seating Side-by-side bucket seating

Numerous features offer the operator and passenger a comfortable ride and provide many operating conveniences.

  • Side-by-side bucket seating provides room for one operator and one passenger
  • Hip restraints serve as a handhold and help keep the operator and passenger in their seats over rough terrain
  • Both seats tilt forward for dry storage and ease of service
  • Choice of adjustable or non-adjustable driver's seat
  • Hour-meter is standard to assist in maintaining regular service intervals
  • Integrated cup holders
  • 12-V outlet is located on the instrument panel
Convenient walk-through operator station Convenient walk-through operator station

The control location and walk-through platform provide easy entry/exit for the operator and passenger.

  • All models feature a park brake indicator light, hour-meter, and tank-mounted fuel gauge as standard equipment
  • Traction assist (differential lock) is hand operated and conveniently located between the operator and passenger seats
  • Traction assist indicator light (Gator™ TH 6X4 only)
  • Glove box is located in the dash to provide a convenient storage area for small tools and operator's manual
  • Grab bar is provided for the passenger
  • Center-mounted key switch
  • Additional storage is provided between the seats
Large 16-gauge cargo box (Gator™ TH 6X4 shown) Large 16-gauge cargo box (Gator™ TH 6X4 shown)

The strong, 16-gauge cargo box allows hauling heavy and bulky cargo.

 

The load of the box is placed directly over the rear wheels, where the load is in the most stable position. The 63.5-com (25-in.) load height for the Gator TS allows easy loading and unloading of material.

Box capacity
 

Gator TS

Volume

286 cu L
(10.1 cu ft)

Weight

227 kg (500 lb)

Manual-tilt cargo box (Gator TS shown) Manual-tilt cargo box (Gator TS shown)

The cargo box can be manually tilted up to allow access to the drive system or to assist in cleaning out the box.

  • A prop rod is provided to hold the box in the upright position for operator convenience.

 

 

Box dump angles (degrees)

 

 

 

 Gator TS

Manual dump

48.5 degrees

Power dump

47.5 degrees

 

The tailgate can be opened or removed for easier cleanout and to carry longer items.

 

The box design includes tie-downs on load guard and box sides.

CAUTION: Carrying extra-long cargo that extends beyond the box can adversely affect stability.

Specifications


Compare the specifications of up to 4 models

Key Specs ts-4x2-utility-vehicle
Current Model
Engine power10.1* kW
13.5 hp
Cargo box dimensions100.3 x 124.5 x 22.9 cm
39.5 x 49 x 9 in.
Cargo box capacity227 kg
500 lb
Towing capacity408 kg
900 lb
Front suspensionIndependent spring over shock, single A-arm
Rear suspensionTwo high-floatation, low pressure tires (solid axles)
Final driveFully enclosed; oil bath
Four wheel driveNo
Fuel capacity5 g
Engine
Type4-cycle gas
Displacement400 cc
24.4 cu in.
Power10.1* kW
13.5 hp
Cooling systemAir
Drivetrain
TransmissionContinuously variable transmission (CVT)
Final driveFully enclosed; oil bath
Four wheel driveNo
Traction assistMechanically Activated Differential Lock
Descent controlNo
Suspension
FrontIndependent spring over shock, single A-arm
RearTwo high-floatation, low pressure tires (solid axles)
Brakes
TypeWet disk in transaxle
Park brakeWet disk, hand operated
Tires
FrontTwo 22.5x10.00-8, 2 PR hi-flotation
RearTwo 25x12.00-9, 2 PR hi-flotation
Dimensions / Capacities
Wheelbase1770 mm
69.7 in.
Front tread centers1270 mm
50 in.
Rear tread centers1220 mm
48 in.
Vehicle weight415 kg
915 lb
Height1108 mm
43.6 in.
Width1525 mm
60 in.
Length104 in.
Ground clearance6.0 (under transaxle) in.
9.8 (foot platform) in.
Fuel capacity5 g
Cargo box dimensions100.3 x 124.5 x 22.9 cm
39.5 x 49 x 9 in.
Cargo box capacity227 kg
500 lb
Payload capacity408 kg
900 lb
Towing capacity408 kg
900 lb
Hitch1.25in hitch is available as an option (BM23839)
Features
ColorGreen/Yellow
Power steeringNo
Battery340 @ -18 C (0 F) CCA
Alternator16.6 @ 3700 rpm (regulated) amp
InstrumentationFuel Gauge, Hour Meter listed in the Sales Manual
StorageCup Holder, Glovebox
SeatingBucket Seats

Offers and Discounts

Studio image of XUV 835r

3.90% APR fixed rate for 84 Months1,2 OR No-Interest if Paid in Full within 12 Months3

on New Gator Utility Vehicles

  • 3.90% APR fixed rate for 84 Months1,2 OR
  • No-interest if paid in full within 12 months3
  • Offers available 04 August 2021 through 29 October 2021

1Offer valid on qualifying purchases made between 04 August 2021 to 29 October 2021. This offer excludes TX Turf Gators™ and ProGators. Subject to approved credit on a Revolving Plan account, a service of John Deere Financial, f.s.b. For consumer use only. No down payment required. 3.9% APR is for 84 months only, regular Revolving Plan rates will apply after that. The regular Revolving Plan rate, which varies over time, is currently 18.25% APR. Available at participating U.S. dealers. Prices and models may vary by dealer. Offer available on new equipment and in the U.S. only. Prices and savings in U.S. dollars.

2Offer valid on qualifying purchases made between 04 August 2021 through 29 October 2021. This offer excludes TX Turf Gators™ and ProGators. Subject to approved installment credit with John Deere Financial, for consumer and ag use only. Down payment may be required. Average down payment is 10%. $13.62 per month for every $1,000 financed. 3.90% APR for 84 months only. Taxes, freight, setup and delivery charges could increase monthly payment. Available at participating U.S. dealers. Prices and models may vary by dealer. Offer available on new equipment and in the U.S. only. Prices and savings in U.S. dollars.

3Offer valid on qualifying purchases made between 04 August 2021 through 29 October 2021. This offer excludes TX Turf Gators™ and ProGators. Subject to approved credit on a Revolving Plan account, a service of John Deere Financial, f.s.b. For consumer use only. No down payment required. Interest will be charged to your account from the purchase date at 17.9% APR if the purchase balance is not paid in full within 12 months or if your account is otherwise in default. Available at participating U.S. dealers. Prices and models may vary by dealer. Offer available on new equipment and in the U.S. only. Prices and savings in U.S. dollars.

Accessories and Attachments

Backup Alarm

Bumper

Front bumper (includes front receiver hitch) Front bumper (includes front receiver hitch)

Composed of strong tubular steel, the front bumper protects the front of the Gator™ Utility Vehicle.

Front bumper/brush guard Front bumper/brush guard

Composed of strong tubular steel, the heavy-duty bumper and brush guard protect the unit from front impacts, as well as add increased protection to the grille and headlights.

Compatible with:

  • TS, TX, TX Turf, TH 6X4 Gas, TH 6X4 Diesel, and TE Utility Vehicles
Front fender guard Front fender guard
#

The front fender guard is composed of strong tubular steel that protects the unit from side impacts.

 

NOTE: The front bumper is standard on the Gator™ TH 6x4 Diesel.

 

The front fender guard requires BM23458 front bumper or BM23459 heavy-duty bumper/brush guard.

Cargo Box

Rubber mat for cargo box Rubber mat for cargo box

The rubber mat is used to provide a surface that has grip and to protect the bottom of the cargo box from scratching.

 

Power lift kit (cargo box) Power lift kit (cargo box)

The power lift kit utilizes an electromechanical actuator for easy raising and lowering of the Gator™ cargo box. A switch is conveniently located on the dash to operate the power lift kit.

 

It is compatible with the following vehicles:

  • Standard Series Gator - 4X2, 4X2 Turf, 6X4, and 6X4 Diesel
  • Traditional Series Gator TS 4X2
101.6-cm (40-in.) poly bedliner 101.6-cm (40-in.) poly bedliner

The poly bedliner is used to provide a surface that protects the bottom of the cargo box from scratching.

This kit includes a bracket assembly that quickly mounts to the deluxe cab structure.    

 

It is compatible with the following vehicles:

  • Traditional Series—TS, TX, TX Turf, and TH 6x4 when equipped with a soft-door or
    hard-door cab
Side storage box Side storage box
#

The side storage box offers over 0.03 m3 (1 cu ft) of storage space to keep valuable items dry and secure.

 

The side storage box is:

  • Lockable
  • Weather resistant

It is compatible with:

  • Gator™ TS, TX, TX Turf, TE Utility Vehicles

  • XUV 620i and 850D Utility Vehicles

  • HPX Gas and Diesel Utility Vehicles

Not compatible with Sunshade

NOTE: The side storage box fits the driver side only.

Cover

Gator cover Gator cover

The cover provides heavy-duty protection for Gators.

  • Dual reinforced air vents let air circulate and help to prevent ballooning in windy conditions
  • Reinforced rear corners for added stability
  • Fabric-coated for maximum water resistance and repellency
  • Elastic shock cord in the bottom hem for a quick custom-like fit
  • Large size fits all standard and traditional series Gators
Ordering information

Please contact the local John Deere dealer for availability and pricing information.

 

Gator cover (large)
Order number: LP93547

Deluxe seat cover Deluxe seat cover

The deluxe thick-cushioned seat cover provides superior protection, all day riding comfort, and lots of storage.

  • Two side mesh stuff beverage pockets hold drinks and a big rear zippered cargo pocket and mesh stuff pocket keep tools and gear readily available
  • Little zippered side key
  • Elastic cord in the hem provides a custom fit
  • Handy fabric storage case and John Deere key ring
  • Three-year warranty
Ordering information

Contact the local John Deere dealer for availability and pricing information.

Deluxe seat cover (medium)
Order number: LP92624

Seat cover Seat cover
#

The cover protects unused seats and renews worn seats:

  • Cushioned for extra comfort
  • Four convenient pockets keep tools and gear within reach
  • Central water drain hole keeps water from pooling
  • Elastic cord at the hem for a custom fit
  • Medium size fits backrests up to 15 in.
  • Large size fits backrests up to 18 in.
  • Two-year warranty

Compatible with Gator™ TS Utility Vehicles.

Ordering information

Contact the local John Deere dealer for availability and pricing information.

Seat cover (medium)
Order number: LP92324

Vehicle cover Vehicle cover
  • Provides year-round weather protection to a vehicle equipped with an operator protection system (OPS) or full enclosure (cab)
  • Heavy-weight polyester fabric for maximum durability and resistance to tear 
  • Polyurethane-coated for maximum water resistance and repellency 
  • Dual reinforced air vents let air circulate and help to prevent ballooning in wind
  • Reinforced rear corners for added durability  
  • Elastic shock cord in the bottom hem for a quick custom-like fit
  • Compatible with the following models:
    • Traditional Series models (TS, TX, TX Turf, TH 6x4, TH 6x4 Diesel, and TE when equipped with a full enclosure), and HPX 4x4, HPX 4x4 Diesel, HPX 4x4 Trail, XUV 620i, and XUV 850D (with OPS or deluxe cab structure and accessories)
    • Gator™ model year 2011 XUV 625i, XUV 825i, XUV 855D, and M-Gator™ A2 Utility Vehicles (with OPS or deluxe cab structure and accessories)
Ordering information

Please contact the local John Deere dealer for availability and pricing information.

 

Vehicle cover (full size—cab or structure)
Order number: LP93107

Drawbar

Hitch drawbar kit Hitch drawbar kit

This kit includes a 32-mm (1.25-in.) solid steel drawbar, galvanized cross pin, and hitch pin kit. It does not include a ball hitch.

 

The drawbar kit may be used on the front or rear of the utility vehicle.

Front Rack

Horn

Horn components Horn components
Horn switch Horn switch

Kit includes:

  • Horn
  • Mounting brackets
  • Wire harness and switch

The switch mounts on the dash of the vehicle. The wiring harness connects to the main vehicle harness.

 

Compatible with following vehicles:

  • CS, CX, TS, TX, TX Turf, TH 6x4, M-Gator™ A1 

NOTE: This kit comes less grease.

Lighting

The beacon light is ideal for those who are looking to provide additional awareness for bystanders.

Beacon light - 48 V mounted on cab Beacon light - 48 V mounted on cab
Beacon light - 48 V mounted on vehicle Beacon light - 48 V mounted on vehicle
Beacon light - 48 V rocker switch Beacon light - 48 V rocker switch

The beacon light kit - 48 V is available for Gator™ Utility Vehicles equipped with a deluxe hard or soft cab and can also be mounted without a cab:

  • Dual voltage compatible, 12 V (TS, TX, TX Turf, TH) or 48 V (TE)
  • Dash-mounted on/off rocker switch
  • LED strobe light
  • Durable nylon housings and scratch-resistant acrylic lens
  • Sealed against water, dust, and corrosion
  • UL-recognized SAE J845 (class 3)
  • Flash rate of 60 + 10 fpm
  • Low current draw of 0.2 amp
  • Use of LED technology provides excellent resistance to damage from external shock and 100 times the useful life of an incandescent lightbulb
  • Measures 1.8 m (74 in.) off the ground when mounted to the hard or soft cab and when mounted to the upright
  • Compatible with Gator TS, TX, TX Turf, TH 6X4 Gas, TH 6X4 Diesel, and TE Utility Vehicles
Beacon light kit Beacon light kit

Rotary light provides excellent visibility to vehicle bystanders:

  • Especially useful for working around properties and job sites
  • Sturdy design allows the Gator to be hauled on a trailer forward or backward at highway speeds with the light installed
  • Contains a breakaway mounting system
    • Sealed package (waterproof)
    • Amber lenses are rugged, shatter-resistant poly material
  • Light assembly bolts to the rear of the cab frame
  • Convenient overhead mounted on/off rocker switch for easy operation
  • As with all Gator electrical kits, the light kit ties into the vehicle's wiring harness for quick installation

Compatible with the following vehicles:

  • All Gator model year 2011-current XUV 625i, XUV 825i, XUV 855D, and M-Gator™ A2 Utility Vehicles when equipped with a deluxe cab frame and electrical kit
  • All Gator HPX model year 2004-current, XUV 620i, and XUV 850D Utility Vehicles when equipped with a deluxe cab frame and electrical kit
  • Traditional Series—TS, TX, TX Turf, and TH 6x4—when equipped with a soft-door or hard-door cab and electrical kit
  • M-Gator A1 when equipped with a hard-door cab and electrical kit
Brake and taillight kit Brake and taillight kit

This kit includes brake lights and taillights. The brake and taillight assembly mount directly to the cargo box. The wiring harness connects to the standard vehicle harness.

 

NOTE: The kit is not intended for use on public roadways.

Compatible with the following models:

  • All model year 2004-2017 Gator™ HPX Utility Vehicles
Rear lights Rear lights
Front light with incorporated mirror Front light with incorporated mirror

The deluxe light kit is compatible with Gator™ Utility Vehicles with or without a cab.

 

Compatible with the following models:

  • Traditional Series
    • All model year TS vehicles
    • Model year 2009 and prior TX, TX Turf, TH 6X4 Gas, TH 6X4 Diesel, and TE vehicles with steel cargo box
Front work light kit Front work light kit

Two 55-W halogen lights provide superb visibility for nighttime operation:

  • Especially useful for working around properties and job sites
  • Sturdy design allows the Gator to be hauled on a trailer forward or backward at highway speeds with the lights installed
  • Light assemblies bolt to the front of the cab frame, creating a consistent lighting pattern
  • Convenient overhead-mounted on/off rocker switch for easy operation
  • As with all Gator electrical kits, the light kit ties into the vehicle's wiring harness for quick installation

Compatible with the following vehicles:

  • All Gator model year 2011-current XUV 625i, XUV 825i, XUV 855D, and M-Gator™ A2 Utility Vehicles when equipped with a deluxe cab frame and electrical kit
  • All Gator HPX model year 2004-current, XUV 620i, and XUV 850D Utility Vehicles when equipped with a deluxe cab frame and electrical kit
  • Traditional Series—TS, TX, TX Turf, and TH 6x4—when equipped with a soft-door or hard-door cab and electrical kit
  • M-Gator A1 when equipped with a hard-door cab and electrical kit
Interior light kit Interior light kit
  • Interior overhead light provides visibility for nighttime operation
  • Light assembly bolts into the overhead panel of the cab for automotive styling
  • Contains an on/off rocker switch for easy operation
  • As with all Gator electrical kits, the light kit ties into the vehicle's wiring harness for quick installation

Compatible with the following vehicles:

  • All Gator model year 2011-current XUV 625i, XUV 825i, XUV 855D, and M-Gator™ A2 Utility Vehicles
  • All Gator HPX model year 2004 to current, XUV 620i, and XUV 850D Utility Vehicles when equipped with a deluxe cab frame and electrical kit
  • Traditional Series—TS, TX, TX Turf, and TH 6x4 when equipped with a soft-door or hard-door cab and electrical kit
  • M-Gator A1—when equipped with a hard-door cab and electrical kit
Rear work light kit Rear work light kit

One 55-W halogen light provides superb visibility for nighttime operation:

  • Especially useful for working around properties and job sites
  • Sturdy design allows the Gator to be hauled on a trailer forward or backward at highway speeds with the lights installed
  • Light assembly bolts to the rear of the cab frame, creating a consistent lighting pattern
  • Convenient overhead-mounted on/off rocker switch enables easy operation
  • As with all Gator electrical kits, the light kit ties into the vehicle's wiring harness for quick installation

Compatible with the following vehicles:

  • All Gator model year 2011-current XUV 625i, XUV 825i, XUV 855D, and M-Gator™ A2 Utility Vehicles when equipped with a deluxe cab frame and electrical kit
  • All Gator HPX model year 2004 to current, XUV 620i, and XUV 850D Utility Vehicles when equipped with a deluxe cab frame and electrical kit
  • Traditional Series—TS, TX, TX Turf, and TH 6x4—when equipped with a soft-door or hard-door cab and electrical kit
  • M-Gator A1 when equipped with a hard-door cab and electrical kit

Mirrors

Exterior mirror kit Exterior mirror kit
  • Rigid design allows the Gator™ to be hauled on a trailer forward or backward at highway speeds with the mirrors installed
  • Adjustable mirror assembly bolts to the cab structure
  • Contains a breakaway mounting system

Compatible with the following vehicles:

  • Traditional Series - TS, TX, TX Turf, TE, and TH 6X4 - when equipped with a soft-door or hard-door cab
  • M-Gator™ A1 when equipped with a hard-door cab

Operator's Station

Shown on TH 6x4 Shown on TH 6x4
Shown on TH 6x4 - doors and windshield open Shown on TH 6x4 - doors and windshield open

The deluxe glass cab includes front windshield (excluding wiper), glass doors, and glass rear window.

For use on the following Gator Utility Vehicles:

  • TS, TX, TH 6X4 Gas, TH 6X4 Diesel, M-Gator A1, TE, and TX Turf

Features

  • Rollover protective structure (ROPS) certified
  • Rear glass window opens to allow ventilation
  • Front windshield can be opened in two positions for ventilation
  • Gas cylinders counter-balance the weight of the windshield when opened
  • Lower front windshield panel is removable without tools, allowing access to remove vehicle hood for service
  • Lockable glass doors
  • Wide variety of individual accessories allows for customizing of cabs

NOTE:

  • BM21653 remote cargo box release kit is required if vehicle is not equipped with cargo box power lift. BM21653 is for use with the TS and steel cargo boxes and is not compatible with model year 2010 to current utility vehicles (deluxe cargo box) or M-Gator A1.
  • BM24804 remote cargo box release kit is required for model year 2010 to current utility vehicles with the deluxe cargo box and is not equipped with a cargo box power lift.
  • Heavy-duty front suspension kit is recommended.
Electrical kit Electrical kit

Required to power electrical cab accessories, this kit includes an overhead console to mount switches that operate electrical accessories, the main cab harness, the 30-A fuse holder, the 30-A fuse, and the roof padding.

 

Compatible with the following vehicles:

  • Traditional Series—TS, TX, TX Turf, TH 6x4, and TH 6x4 Diesel when equipped with a soft-door or hard-door cab
  • M-Gator™ A1—when equipped with a hard-door cab
Rubber floor mat Rubber floor mat

Washable mat protects the floor and minimizes dust, debris, and noise in the operator station.

 

Compatible with Gator™ TS 4X2, TX 4X2, TH 6X4 Gas, TH 6X4 Diesel, TX Turf, and TE Electric-145 Utility Vehicles.

The forced-air heater kit uses a dash-mounted heater powered by gasoline from the vehicle's fuel system. Since the heater is using fuel instead of warm coolant from the engine to generate heat, the cab heat is available more rapidly. The desired cab temperature can be reached with or without the engine running.

  • Dash-mounted, five-position control dial to adjust for operator comfort
  • Position 1 is off
  • Positions 2 to 5 offer four heat levels (low, medium, high, and boost, respectively)
  • LED indicator light for operation
  • Dash-mounted, directional louver provides windshield defrosting and complete operator comfort
  • Second outlet provides heat to the foot well area
  • Compatible with the following T Series models: TS, TX, TX Turf, and TH 6x4 (gas)

Specifications

  • Heat output of 0.8 kW to 2.2 kW (2900 Btu/hr to 7500 Btu/hr)
  • Gasoline consumption of 0.10 L/hr to 0.27 L/hr (0.02 gph to 0.07 gph)
  • Air throughput of 0.85 m 3/min to 1.42 m 3/min (30 cfm to 70 cfm)
  • Power consumption at startup of 250 W (at 12 V)
  • Power consumption in operation of 8 W to 30 W
Operation of forced-air heater

Upon startup, the heater's control module runs a self-diagnostic check for safety. Then, the blower begins to increase speed as fuel is fed into the burner. Once the combustion process has stabilized, the glow plug is switched off. The heater continues to run until the thermostat senses the temperature has reached the setting on the control dial.

 

The heater will then switch to the next lowest setting. The heater will return to the higher setting as the temperature drops below the setting on the control dial. If the heater switches itself off, it will automatically restart when the temperature drops below the setting on the control dial.

 

If the heater's control module senses an incorrect air-intake volume, incorrect exhaust volume, incorrect fan speed, flame absence, flame loss, overheating, control dial failure, sensor failure, blower failure, glow plug failure, fuel pump failure, incorrect voltage, short-circuit or control module failure, the heater is immediately switched off and a fault code is recorded. 

 

When the heater is switched off, the green light goes off and fuel is no longer fed to the burner. The glow plug remains switched on for 30 seconds to clear the heater of combustible residue. To prevent damage to the heater, the blower continues to run until the heater is cool.

Occupant Protective Structure with Canopy - 56B0MBM23203

Shown on TX Gator Shown on TX Gator
#

Features of the sunshade:

  • Made from 100 percent solution dyed, all-weather ultraviolet resistant polyester designed specifically to handle stress and resist tearing.
  • Urethane coating is added to the fabric, adding stability and increased moisture and mildew resistance, with minimal shrinking or stretching.
  • Heavy-duty powder coated black steel frame that bolts directly to the vehicle chassis.
  • Sunshade dimensions: 864 mm by 1270 mm (34 in. by 50 in.)
  • Not compatible with side storage box
Visor kit Visor kit

The conveniently placed overhead visor provides sun protection.

 

It is compatible with the following vehicles:

  • All Gator model year 2011-current XUV 625i, XUV 825i, XUV 855D, and M-Gator™ A2 Utility Vehicles when equipped with a deluxe cab frame
  • All Gator HPX model year 2004-current, XUV 620i, and XUV 850D Utility Vehicles when equipped with a deluxe cab frame
  • Traditional Series—TS, TX, TX Turf, and TH 6x4—when equipped with a soft-door or hard-door cab
  • M-Gato A1 when equipped with a hard-door cab
Windscreen kit Windscreen kit

The windscreen is constructed of tough, 4.76-mm (3/16-in.) thick tinted acrylic.

  • Easily attaches to and detaches from the vehicle
  • Height can be set to accommodate the operator preference
Dimensions

 

 Width

 940 mm (37 in.)

 Height

 457 mm (18 in.)

 Depth

 127 mm (5 in.)

Rear Receiver Hitch

Rear hitch Rear hitch

The rear hitch acts as a mounting point for rear and tow-behind attachments:

  • Gator™ TS has a 408-kg (900-lb) towing capacity.
  • Gator TH 6x4 has a 635-kg (1400-lb) towing capacity.
  • Gator TH 6x4 Diesel has a 726-kg (1600-lb) towing capacity. 
  • Gator TE has a 272-kg (600-lb) towing capacity. 
  • Gator 6X4 Diesel has a 636-kg (1400-lb) towing capacity. 
Rear receiver hitch Rear receiver hitch

This versatile hitch accepts a 1.25 in. (31.75 mm) drawbar. 

No ball mount comes with the hitch.

Seat

Adjustable driver seat—forward position Adjustable driver seat—forward position
Adjustable driver seat—aft position Adjustable driver seat—aft position

This kit provides a slide-rail system that allows five 14-mm (9/16-in.) fore-aft positions.

Speed Control

Rough terrain kit Rough terrain kit

Ideal for operators who are consistently driving over rough terrain. The damper assists the operator by modulating throttle input.

Compatible with Gator™ TS, TX, TH, and M-Gator™ A1 Utility Vehicles.

Sprayers

High-performance 45-gal. (170-L) Gator bed sprayer High-performance 45-gal. (170-L) Gator bed sprayer
#

The high-performance Gator bed sprayer is designed to work with Gator vehicles equipped with the deluxe cargo box or steel bed. With a 45-gal. (170-L) capacity, high volume electric pump, and premium pistol grip spray gun, it provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray and de-icer. Engineered brackets secure the sprayer to the Gator bed with no tools, or additional tie-downs required.

NOTE: Sprayer shown above with optional 150-in. precision boom (LP22885).

High-performance features:

  • 45 psi, 3.6 gpm SHURflo® diaphragm-type pump is designed for high hour applications and can be run dry without damage
  • Premium pistol grip spray gun, designed for single hand mist to 35-ft stream
  • Equipped with a 20-ft hand wand hose with side mount hose tender for convenience
  • Glycerin-filled pressure gauge and TeeJet™ pressure regulation/recirculation valve
  • Choice of booms (sold separately)
  • On/off capabilities in the palm of your hand with the included sprayer remote control (LP22912)
  • 12V plug included with wiring harness, complete with quick-disconnects, for convenient electrical hookup
  • Brackets secure to Gator bed, no tools or additional strapping required after initial set-up
  • Control valve channels spray to either the boom or spray wand
  • Rugged translucent yellow tank with molded fill level indicators (in gallons)
Specifications

Capacity

45 U.S. gal. (170 L)

Pump

Type

Electric motor and diaphragm

Manufacturer

SHURflo® 

Operating pressure

45 psi

Current draw

7 amp

Valve material

Viton® 

Diaphragm material

Santoprene™

Spray flow rate

3.6 U.S. gpm (13.6 L/min)

Sump strainer

Stainless steel

Remote spray method

Spray wand

Poly, alloy, and brass with Viton components

Tip material

Brass and stainless

Adjustment Fan-to-stream
Hose length 20-ft - 1/2-in. nylon reinforced rubber

Gauge

Glycerin filled

Spray control

Pressure regulation/recirculation

Remote control

12V receiver with dual FOB remote on/off

Boom (sold separately)

Option 1 150-in. spray width precision folding (5 tip)
Option 2 120-in. spray width (3 tip)
Option 3 24-ft boomless nozzle

Mounting

Steel bed Custom tailgate clamp mounting
Deluxe cargo box Custom brackets secure to tie-downs

Compatibility

All Gator models (except CX)

Shipping weight

56 lb (25 kg)

Net weight

52 lb (23 kg)

 

Ordering information

Contact the local John Deere dealer for availability and pricing information.

 

High-performance 45-gal. (170-L) Gator bed sprayer
Order number: LP22908

 

SHURflo is a U.S.-registered trademark of Sta-Rite Industries, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.

25-gal. (95-L) bed sprayer 25-gal. (95-L) bed sprayer

This 25-gal. (95-L) Gator™ bed sprayer is a self-contained unit that conveniently sits in the bed of a steel bed Gator, ATV EXT or Gator CX.
 
It allows the operator to spray trees and shrubs with the spray wand or broadcast spray in a 10-ft swath with the boom.

The 25-gal. (95-L) yellow tank has four rubber feet bolted to the bottom to protect and stabilize the sprayer.

  • Sprayer is held in place with the end gate support frame
  • Large threaded cap makes fill-up easy
  • Easy-to-read gallon marks are molded in
  • A built-in sump is provided to completely clean out the spray material

 

The SHURflo® pump operates at 100 psi and pumps 2.1 gpm.

  • Complete wire harness with switch plugs into the 12-V power outlet on the vehicle

 

The spray boom includes three floodjet nozzles with check valves to prevent dripping:

  • Boom is supported by vehicle tailgate
  • Spray boom is easily removed when not needed

 

The sprayer is equipped with a high-quality Spraying Systems Co.® spray wand:

  • 14-in. wand with adjustable brass spray tip
  • 19-ft hose included

 

The 25-gal. bed sprayer fits Gators and ATV EXT models, which have cargo boxes.


Specifications

 

 

Capacity 25 U.S. gal. (95 L)
Pump  
Type Electric motor and diaphragm
Manufacturer SHURflo
Operating pressure 100 psi
Current draw 7 amp
Valve material Viton®
Diaphragm material Santoprene™
Strainer Stainless steel
Boom spray width 120 in. (305 cm)
Spray tip(s) Three TF-VP3
Spray flow rate 2.1 U.S. gpm (7.9 L/min)
Remote spray 19-ft hose with adjustable polypropylene handgun with 14-in. wand
Handgun material Polypropylene with Viton components
Adjustment Fan-to-stream
Shipping weight 35 lb (16 kg)
Warranty Two year

 

Ordering information 
 
Contact the local John Deere dealer for availability and pricing information.


25-gal. (95-L) bed sprayer
Order number: LP20850

SHURflo is a U.S.-registered trademark of Sta-Rite Industries, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.

170-L (45-gal.) Gator bed sprayer 170-L (45-gal.) Gator bed sprayer

The sprayer is a self-contained unit that allows the user to spray trees and shrubs with the spray wand or broadcast spray in a 3.05-m (10-ft) swath with the spray boom.

Key features
  • Shurflo pump operates at 6.9 bar (100 psi) and pumps 8 L/min (2.1 gpm)
  • Spray boom is easily removed when not needed
  • Fully adjustable brass spray wand tip achieves streams up to 9.15 m (30 ft)
  • Mounts without the use of tools
  • Brackets secure to Gator bed, no bungees required
  • A built-in sump is provided to completely clean out the spray material
  • Includes Gator accessory wiring harness, complete with quick-disconnects, for convenient electrical hookup
  • Check valves in boom tips prevent siphoning and dripping
  • Equipped with a 5.8-m (19-ft) hand wand hose for convenience
  • Large threaded cap makes filling up easy
  • Easy-to-read gallon marks are molded in
Ordering information

Contact your local John Deere dealer for availability and pricing information.

170-L (45-gal.) Gator bed sprayer
Order number: LP20851

Shown on TH 6x4 with HP 45-gal. Sprayer Shown on TH 6x4 with HP 45-gal. Sprayer

The standard Gator boom is compatible with all Gator sprayer models and is sold separately for the HP Gator sprayers. This fixed boom is conveniently sized at 43 in. (1.1 m) and does not extend wider than the Gator bed, but it is perfect for covering ground quickly and thoroughly with a 120-in. (3-m) spray swath.

 

The boom is ideal for basic spraying application. Three tips and check valves round out this offering (boom only, mounting brackets are provided with sprayers).

Boom Features:
  • 43-in. (1.1-m) boom with three tips
  • Check valves prevent siphoning and dripping
  • Sold separately for:
    • HP 45-gal. Gator Bed Sprayer
    • HP 90-gal. Gator Bed Sprayer
    • HP 45-gal. Gator Bed Sprayer – XUV 550
Shown on TH 6x4 with HP 45-gal. Sprayer Shown on TH 6x4 with HP 45-gal. Sprayer
Shown on TH 6x4 with HP 45-gal. Sprayer Shown on TH 6x4 with HP 45-gal. Sprayer

The 150-in. (3.81-m) precision boom is compatible with the HP sprayers. This folding boom is made to cover ground quickly and thoroughly with five precision spray tips, TeeJet™ nozzle bodies and commercial grade diaphragm check valves. The outer tips offer versatility with built-in shut offs to allow an adjustable 90-in. (2.3-m), 120-in. (3-m), or 150-in. (3.8-m) spray swath.

150-in. (3.8-m) precision boom features:
  • Folding spring hinge
  • Breakaway design
  • Five TeeJet tips and nozzle bodies
  • Adjustable spray swath (90 in., 120 in., 150 in.)
  • 1/2-in. industrial-grade rubber hose
  • Designed to work with
    • HP 45-gal. Gator™ Bed Sprayer
    • HP 90-gal. Gator Bed Sprayer
    • HP 45-gal. Gator Bed Sprayer – XUV 550

 

 

 

TeeJet is a registered trademark of Spraying Systems Company.

Shown on TH 6x4 with HP 90-gal. Sprayer Shown on TH 6x4 with HP 90-gal. Sprayer
HP 90-gal. Sprayer HP 90-gal. Sprayer

The 24-ft (7.3-m) boomless spray nozzles are compatible with all HP sprayers. This boom is perfect for covering ground quickly and thoroughly with a 24-ft (7.3-m) spray swath. It is ideal for uneven terrain or where precision spray application is not necessary. TeeJet™ nozzle bodies and commercial grade diaphragm check valves round out this offering.

Boomless spray nozzles feature
  • Three TeeJet tips and nozzle bodies
  • Commercial-grade diaphragm check valves
  • 1/2-in. (12.7-mm) industrial-grade rubber hose
  • Designed to work with all HP sprayers :
  • HP 45-gal. Gator™ Bed Sprayer
  • HP 90-gal. Gator Bed Sprayer
  • HP 45-gal. Gator Bed Sprayer – XUV 550

 

 

 

 TeeJet is a registered trademark of Spraying Systems Company.

45-gal. (170- L) Tow-Behind Sprayer 45-gal. (170- L) Tow-Behind Sprayer

The HP 45-gal. (170-L) Tow-Behind Sprayer offers the ultimate in performance and versatility. With a 45-gal. capacity, high volume electric pump, and premium pistol grip spray gun, it provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray and deicer. It is the perfect match for the customer who wants extreme performance. 

 

The heavy-duty frame rolls smoothly on 15x6 tires that minimize ground compaction and have a low profile, which maintains a low center of gravity for excellent stability. Cover ground quickly with flexible boom options; a 150 in. (3.8 m) precision folding, 120-in. (3-m) standard three tip, 24-ft (7.3-m) boomless, or no boom at all (boom sold separately).

HP features:
  • 45 psi, 3.6 gpm SHURflo® diaphragm-type pump is designed for high hour applications and can be run dry without damage
  • Premium pistol grip spray gun, designed for single hand mist to 35 ft (10.7 m) stream
  • Front-mount hose tender for easy hose access and storage
  • Glycerin filled pressure gauge
  • TeeJet™ pressure regulation/recirculation valve
  • Includes sprayer remote control
Additional features
  • Easy boom removal for added convenience
  • Control valve channels spray to either the boom or spray wand
  • Rugged translucent yellow tank with molded fill level indicators (in gal.)
Boom options (sold separately):
  • 150-in. (3810-mm) precision spray boom
  • 24-ft  (288-in.) boomless spray nozzles

 

SHURflo is trademark of SHURflo, LLC. TeeJet is a registered trademark of Spraying Systems Company.

45-gal. (170-L) tow-behind sprayer 45-gal. (170-L) tow-behind sprayer

The 45-gal. (170-L)  trail-type sprayer is equipped with a boom that sprays a wide, 120-in. width.

  • Three nozzles for efficient broadcast spraying
  • Boom folds up against the tank for storage

A 20-ft hose and handgun are provided.

  • The 20-ft hose and handgun are helpful when spraying trees or other remote areas that cannot be reached with the sprayer itself
  • A 14-in. wand on the handgun is standard equipment

The heavy-duty frame rolls smoothly on 15x6 tires that minimize ground compaction.

  • Low center of gravity gives excellent stability
  • Equipped with a 4-position hitch
  • Rear of the frame is designed so the sprayer will stand upright during storage to reduce the amount of space required

Additional features include:

  • Diaphragm-type pump designed for high-hour commercial applications; it can be run dry without damage
  • The spray wand is constructed of non-corrosive polypropylene material with Viton® components for remote spray jobs
  • Two-wire fused wiring harness complete with quick-disconnects for convenient electrical hookup
  • Large cap to easily fill up the tank
  • Control valve to channel the spray to the boom or handgun
  • Rugged translucent yellow tank with molded fill-level indicators (in gallons)
Specifications

Capacity

45 U.S. gal. (170 L)

Pump

Type

Electric motor
and diaphragm

Manufacturer

SHURflo® 

Operating pressure

100 psi

Current draw

7 amp

Valve material

Viton® 

Diaphragm material

Santoprene™

Strainer

Stainless steel

Boom spray width

120 in. (305 cm)

Spray tip(s)

Three #11008VP

Spray flow rate

2.1 U.S. gpm (7.9 L/min)

Remote spray method

20-ft hose with adjustable polypropylene handgun with 14-in. wand

Handgun material

Polypropylene with Viton components

Adjustment

Fan-to-stream

Tires

15x6-6 pneumatic

Wheel bearings

Roller bearings

Axle diameter

1 in. (2.5 cm)

Hitch

Pin and spring clip, four height positions

Weight - empty

80 lb (36.3 kg)

Weight - full

456 lb (207 kg)


Compatible with all Gator models except XUV 550, XUV 550 S4, and RSX Utility Vehicles.

Ordering information

Contact the local John Deere dealer for availability and pricing information.

 

45-gal. (170-L) tow-behind sprayer
Order number: LP20485

 

SHURflo is a U.S.-registered trademark of SHURflo, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.

Spreaders

17AT Cart 17AT Cart
  • 0.5-m 3 (17-cu ft) capacity
  • 453.6-kg (1000-lb) load limit
  • Copolymer polypropylene is compression molded for optimum thickness in all areas and maximum durability
  • Heavy-duty, reinforced structural frame with a 25.4-mm (1-in.) diameter, one-piece axle to handle weight, speed, and bumps
  • Spring-loaded dump latch for easy dumping and positive lock to prevent accidental unlocking when being towed
  • Double-sealed, high-speed roller bearings to handle a 48-km/h (30-mph) maximum speed
  • Heavy-duty polyethylene bed
    • Accepts dividers to separate cargo (template included)
  • All-terrain knobby tires
    • Provides good flotation and traction in mud, sand, and other wet or soft areas
    • Flexes over bumps and ruts for a smoother, more controlled ride
    • Minimizes ground compaction to save turf and prevent ruts in soft ground
  • Poly fenders to keep the operator, cart, and vehicle clean
  • Suitable for use with most John Deere utility vehicles equipped with a 48-mm (1.875-in.) ball hitch, including Gator™ Utility Vehicle models TX, TX Turf, TH 6x4, TH 6x4 Diesel, all HPX 4x4 models, and all XUV models
  • Quality and styling compatible with other John Deere equipment
Ordering information

Contact your local John Deere dealer for availability and pricing information.

 

17AT Cart

Order number: LPPCT17ATJD

TX hitch and control box TX hitch and control box

The spreader hitch and control kits were designed to mount salt and fertilizer spreaders which are engineered to fit Gator™ Utility Vehicles.

 

Features:

  • Hitch frames are spring loaded for quick attach/detach spreader capabilities
  • Hitch can be easily lowered by the use of spring-loaded pins, promoting easy bed or engine access
  • Electronic control box is weather resistant and enables variable-speed application from the comfort of the operator’s seat

Spreader hitch and controls kit includes:

  • Spreader hitch frame
  • Electronic control box and wiring
21 Steel Utility Cart 21 Steel Utility Cart

The 21 Steel Utility Cart is the ideal companion for the Gator™ Utility Vehicle:

  • 454-kg (1000-lb) load limit
  • Dump angle of 35/40 degrees
  • Spring-loaded dump latch for easy dumping and positive lock to prevent accidental unlocking when being towed
  • Large pneumatic tires
    • Provide good flotation in mud, sand, and other wet or soft areas
    • Flex over bumps and ruts for a smoother, more controlled ride
    • Minimize ground compaction to save turf and prevent ruts in soft ground
  • Unique bracket less tailgate means no side channels to obstruct materials when emptying
  • When shoveling, recessed flat bolt heads stay out of the way
  • Heavy-duty, reinforced one-piece solid undercarriage
  • Contoured corner bed design
  • Suitable for use with most John Deere utility vehicles equipped with a 48-mm (1-7/8-in.) ball hitch, including Gater™ Utility Vehicle models TX, TX Turf, TH 6x4, TH 6x4 Diesel, all HPX 4x4 models, and all XUV models
Ordering information

Contact the local John Deere dealer for availability and pricing information.

 

21 Steel Utility Cart
Order number: LPUT21JD

Suspension

Heavy-duty front suspension kit Heavy-duty front suspension kit

The heavy-duty front suspension kit improves ride and handling while hauling heavier loads.

  • Heavy-duty front shock absorbers with higher-strength springs replace the standard shocks
  • Spring support is adjustable to five positions
  • Heavy-duty suspension kit is recommended if the Gator™ utility vehicle is equipped with a cab or front blade attachment
    • The front blade attachment is not compatible with TH 6X4 Diesel Utility Vehicles.

NOTE: The M141507 wrench to adjust the weight setting is available through Service Parts.

Tire Chains

Tire chains Tire chains

Tire chains increase traction dramatically under ice and snow conditions.

NOTE: Not intended for use on all four rear tires on the TH 6x4 and TH 6x4 Diesel.
Tire chains Tire chains

Tire chains increase traction dramatically under ice and snow conditions.

NOTE: Not intended for use on all four rear tires on the TH 6x4.

Winch

WARN winch WARN winch

This strong, 12-V winch has an impressive pulling capacity of 1134 kg (2500 lb). It is equipped with a water-resistant contactor that supplies the amperage required for higher pulling capacities. The kit also includes a wiring harness that allows for a quick connection to the winch at the front of the Gator™ utility vehicle. The rear wiring harness with quick connection can be purchased through Parts.

The winch has a 3.05-m (10-ft) lead and a water-resistant remote for safe-distance operation. It also comes with a four-way roller fairlead to minimize rope abrasion and pulling resistance.

The kit comes with the winch, receiver mounting plate, and wiring for front mount. This winch is compatible with 31.75-mm (1.25-in.) front and rear receiver hitches.

NOTE: Requires front receiver hitch for front mount. Requires rear receiver hitch for rear mount. Requires AM137110 rear multi-mount harness for rear mount. VGA10459 365.8-cm (144-in.) battery cable is required for TH 6X4 Diesel and M-Gator™ A1 Utility Vehicles.

WARN is a trademark of WARN Industries, Inc.

Winch Mounting Kit

Winch accessories kit Winch accessories kit

Double the pulling power, change the pulling direction, and keep the winch in proper working order.

The accessories kit is essential gear for operators getting the most out of their winch:

  • Effectively anchors to trees/boulders
  • Change the pulling direction
  • Double the pulling capacity

The accessories kit includes:

  • Flexible tree strap
  • Snatch block
  • Shackle

Each kit comes in a black Cordura® heavyweight-nylon soft case.

 

Cordura is a trademark of INVISTA.

Windshield

Especially useful for working around properties and job sites, the windshield washer kit includes the following:

  • Mounting bracket
  • Hardware
  • Spray nozzle
  • Large reservoir with electric pump
  • Harness and hose

The reservoir assembly bolts to the bottom-right rear of the cab structure. A convenient overhead-mounted on/off rocker switch controls the windshield wiper and washer fluid. As with all Gator™ electrical kits, the washer kit ties into the vehicle's wiring harness for quick installation.

Compatible with the following vehicles:

  • Traditional Series—TS, TX, TX Turf, and TH 6x4 when equipped with a soft-door or hard-door cab and electrical kit
    • TH 6x4 Diesel requires cargo box power lift
  • M-Gator A1 when equipped with a hard-door cab and electrical kit

Kit includes:

  • Wiper
  • Motor assembly
  • Mounting hardware

A convenient overhead mounted on/off rocker switch controls the windshield wiper and washer fluid (if equipped). As with all Gator™ electrical kits, the wiper kit ties into the vehicle's wiring harness for quick installation.

Compatible with the following vehicles:

  • Traditional Series—TS, TX, TX Turf, and TH 6x4—when equipped with a soft-door or hard-door cab and electrical kit
  • M-Gator™ A1 when equipped with a hard-door cab and electrical kit