×
Quick Used Equipment Filter












used search tag

See All Locations

XUV835M HVAC UTILITY VEHICLE

Crossover Utility Vehicle

  • Climate-controlled cab with heat and air conditioning
  • Smooth, power steering
  • Cargo box with spray-in liner, brake and taillights
  • Up to 4,000-lb  towing capacity
Starting At:$28,769.00
Test Drive
View Product Brochure



Features



You will feel confident and comfortable, even on tough terrain, with a full-size Gator™ Utility Vehicle. You will feel stable with a low center of gravity and a wide stance. Engine braking and four-wheel hydraulic disc brakes keep you in control on steep descents, even when fully loaded. The power steering on M- and R-Trim vehicles, is smooth and responsive.

Standard four-wheel drive with front and rear differential locks
Dash mounted four-wheel drive and rear differential lock switches Dash mounted four-wheel drive and rear differential lock switches

With standard four-wheel drive and differential lock, both instantly available with the flip of a switch, you can get where you are going.

Dual A-arm front and rear independent suspension
Rear suspension and ground clearance Rear suspension and ground clearance

The independent suspension provides a smooth ride as 203 mm (8 in.) of front suspension travel and 229 mm (9 in.) of rear suspension travel cushions bumps and glides over ruts. And clearing rocks and roots is no problem with 284 mm (11.2 inches) of ground clearance.

Tires for any terrain
Terra Hawk all-terrain tire Terra Hawk all-terrain tire
Maxxis® Bighorn® 2.0 extreme terrain radial tire Maxxis® Bighorn® 2.0 extreme terrain radial tire
Predator Heavy-Duty all-terrain radial tire Predator Heavy-Duty all-terrain radial tire

Full-Size Gator Utility Vehicles are available with three tire options:

  • Terra Hawk all-terrain tires
    • Tread pattern and wide footprint provide excellent traction with minimal impact on terrain
  • Maxxis Bighorn 2.0 extreme terrain radial tires
    • Radial construction provides shock absorption, allowing for a smoother ride
    • Non-directional tread pattern provides predictable cornering and claws up roots and rocks
  • Predator Heavy-Duty all-terrain radial tire
    • Radial construction provides shock absorption, allowing for a smoother ride
    • Flat profile increases footprint area, reducing ground pressure
    • 8-ply rating delivers up to three times the life of Bighorn tires

 

Maxxis® Bighorn® is registered trademark of Cheng Shin Rubber Ind. Co., Ltd.

Full-size Gator™ XUVs are built to work hard and go the extra mile.

Heavy-duty frame
Underside view of XUV865M Underside view of XUV865M
Underside view of XUV825M S4 Underside view of XUV825M S4

The hefty frame is designed to stand-up to all the bumps and bends of the trail, and the standard front skid plate protects key components from damage.

Constant velocity boot protection
Constant velocity boot protection Constant velocity boot protection

Constant velocity joints are enclosed to keep water and dirt out. A protector shield protects the boot from trail debris.

Automotive-grade panels and optional protection packages
TrueTimber® KANATI camo XUV865R with optional Premium Protection Package TrueTimber® KANATI camo XUV865R with optional Premium Protection Package

The hood and side panels are made of automotive-grade materials that resist scratches and dents, and the cargo box is made of tough composite material that resists dents and rust. Optional protection packages look tough and provide even more protection.

 

TrueTimber® is a trademark of True Timber Outdoors Holding Company, LLC.

Instrument display, shift lever, and switches (shown on XUV835R Signature Edition) Instrument display, shift lever, and switches (shown on XUV835R Signature Edition)

When you sit behind the wheel of a full-size Gator™ Utility Vehicle, you will be reminded of your favorite pick-up truck. There are controls at your fingertips, an easy-to-read instrument panel, and outlets to recharge your phone.

 

Shift from park and into gear with a throw of a single lever. Power steering on M- and R- trim vehicles is smooth and responsive.

 

When the going gets tough, you can instantly engage four-wheel drive and rear differential lock with switches. Even at night, the backlit switches are easy to see. If a front wheel starts to slip, the front differential automatically locks to pull you through.

When you hop into the seat of a full-size Gator™ Utility Vehicle, you will notice there’s seating for you, plus two.

Three-passenger seating with room to spare
40/60 split three-passenger bench seat 40/60 split three-passenger bench seat
Operator platform Operator platform

The adjustable operator’s seat and tilt steering lets drivers of all sizes get comfortable, and the passenger grab handles help everyone feel secure. The low step height and generous opening between seat base and fender is even designed to accommodate bulky work boots.

Climate-controlled comfort
HVAC controls HVAC controls
Partially-open door windows and fully-open windshield Partially-open door windows and fully-open windshield

On cab vehicles, you will enjoy standard heating and air-conditioning that will keep you comfortable in every season, and the tight-closing doors help seal out dust and reduce noise. When you want to let in the breeze, you can also roll down the windows and open the front windshield.

Upgrade to R-trim refinements
Stone colored dash with sport steering wheel Stone colored dash with sport steering wheel
Headliner, sun visors, rearview mirror, and dome light Headliner, sun visors, rearview mirror, and dome light

R-trim vehicles have an upgraded stone-colored cab interior with headliner and rear panel to reduce noise. Standard LED headlights, sun visor, dome light, rearview mirror, and sport steering wheel round out the package.

Stone cloth seat
Stone cloth seat Stone cloth seat

R-trim vehicles also include a stone cloth seat that keeps cool in the hot sun and warms up quickly in the winter.

XUV835R with AutoTrac Ready option XUV835R with AutoTrac Ready option
Interior of XUV835R with Gen 4 4640 Universal Display Interior of XUV835R with Gen 4 4640 Universal Display

Precision ag technologies have changed the way we farm, and John Deere has been at the forefront of that change. Adding the AutoTrac™ assisted steering system and JDLink™ Modem options to Gator Utility Vehicles brings precision ag technology to farms of all sizes.

 

The AutoTrac Ready option enables hands-free steering through the field decreasing overlap and lowering input costs while reducing operator fatigue. The JDLink Modem option connects your vehicle to the John Deere Operations Center so the vehicle can be managed with the rest of your fleet.

Simplify field boundaries

  • Check field boundaries and identify hazards as the Gator Utility Vehicle steers itself along established boundary lines.
  • Create new boundary lines, even when the soil is too wet for larger equipment.

 

Improve soil mapping

  • The days of picking a tree across the field to navigate are over. Use guidance lines to create a sampling grid and let your Gator Utility Vehicle keep you on track as you pull plugs across the field.

 

Connect your Gator Utility Vehicle to the rest of your fleet

  • Leave the USB drives at home as you wirelessly send your data to and from your Gator Utility Vehicle.
  • A planter operator can flag the exact location of a large rock so the Gator UV can be sent to the location to remove the hazard.

 

Save time and stop waiting for the perfect day to spray

  • When paired with a tow behind sprayer and rate controller, the Gator Utility Vehicle’s lighter weight allows work to be completed when the ground is too wet for larger equipment.
  • Speed through spraying by allowing the Gator Utility Vehicle to steer a predefined path around buildings and fence rows.

 

Track productivity, maintenance, and machine vitals

  • Track the current and past locations of your Gator Utility Vehicle in the John Deere Operations Center, just like the rest of your fleet.
  • Know when your Gator Utility Vehicle is ready for scheduled maintenance

 

Share StarFire™ Receiver and Universal Display

  • You can leave precision ag technology components installed year-round or share your StarFire Receiver and Universal Display with another piece of equipment.

The full-size Gator™ XUV can haul 454 kg (1000 lb), so load it up with confidence. You can also make fewer trips with 1814 kg (4000 lb) of towing capacity and a standard 51-mm (2-in.) receiver hitch.

Built-tough cargo box
Cargo box (shown with spray-in liner and optional taillight protectors) Cargo box (shown with spray-in liner and optional taillight protectors)
Cargo box converted to flatbed Cargo box converted to flatbed

The cargo box resists dents, scratches, and rust because it is made from a tough composite material. You will have no problem securing loads with integrated tie bars and 14 tie-down points. You can also convert the cargo box to a flatbed when you need to haul big and bulky loads.

 

The cargo box measures 1143 mm (45 in.) long, 1320 mm (52 in.) wide, and 305 mm (12 in.) deep.

One-handed tailgate
Tailgate handle Tailgate handle

Since your hands are always full, the tailgate can be opened and closed with one hand. You can also lower the tailgate to carry longer items or remove it for easy cleanout.

Power lift
Deluxe cargo box unloading rocks Deluxe cargo box unloading rocks

To save your back, the optional cargo box power lift empties heavy loads with the push of a button.

812-cc (49.6-cu in.) gasoline engine and drivetrain 812-cc (49.6-cu in.) gasoline engine and drivetrain

The XUV835 and XUV825M S4 Gator™ Utility Vehicles are powered by an electronic fuel injection (EFI) gasoline engine with liquid-cooled, dual-overhead cams. This engine is designed to provide maximum power and fuel efficiency to muscle through tough jobs.

 

It also has plenty of torque in low range, and fast speeds in high range. The enclosed drivetrain automatically adjusts for fast acceleration, along with powerful hauling and hill-climbing capabilities.

One-row full-size Gator XUVs come packed with places to store tools, gear, and beverages.

Cup holders
Four cup holders and center tray (shown on XUV835E) Four cup holders and center tray (shown on XUV835E)
Cab door cup holder and pocket Cab door cup holder and pocket

The dash has four cup holders, and cab vehicles have a cup holder in each door.

Dash and under-seat storage
Under seat storage (shown on XUV835E) Under seat storage (shown on XUV835E)
Glove box, storage pocket, and two dash bins (shown on XUV835M cab) Glove box, storage pocket, and two dash bins (shown on XUV835M cab)

The vehicles also feature an enclosed glove box, center tray, dash storage pocket and under-seat storage. Depending on the configuration, vehicles may have up to three additional dash bins and under-hood storage.

Green and yellow XUV835R Signature Edition with included Ultimate Protection Package Green and yellow XUV835R Signature Edition with included Ultimate Protection Package
Olive and black XUV865M with cab and optional brush guard Olive and black XUV865M with cab and optional brush guard
TrueTimber® KANATI camo XUV865R with optional Premium Protection Package TrueTimber® KANATI camo XUV865R with optional Premium Protection Package
Desert sand, XUV835M Honor Edition with included brush guard Desert sand, XUV835M Honor Edition with included brush guard

You will get noticed with the distinctive styling of full-size Gator™ XUVs. Available in four colors, with various protection packages, and more than 100 attachments, you can create a custom look that will turn heads.

 

TrueTimber is a trademark of True Timber Outdoors Holding Company, LLC.

Large fuel tank fill opening Large fuel tank fill opening

Full-size Gator™ XUVs have a large 42.8-L (11.3-gal.) fuel tank so you go further between fill ups. A 76-mm (3-in.) diameter fill opening reduce spills.

Specifications


Compare the specifications of up to 4 models

Key Specs xuv835m-hvac-utility-vehicle
Current Model
Engine power43* kW
54* hp
Cargo box dimensions1143 x 304.8 x 1320 mm
45 x 12 x 52 in.
Cargo box capacity (weight)454 kg
1000 lb
Towing capacity907 kg
2000 lb
Front suspensionFully independent dual A-Arm with adjustable coils; 7.9 inches (200.7 mm) of travel
Rear suspensionFully independent dual A-Arm with adjustable coils and sway bar; 9.1 inches (231.14 mm) of travel
Final driveTwo speed, oil bath
Four wheel driveOn-demand true four-wheel drive system
Fuel capacity42.4 L
11.2 U.S. gal.
Engine
Type4-cycle gas, Electronic Fuel Injection (EFI)
Displacement812 cc
Power43* kW
54* hp
Cooling systemLiquid
Drivetrain
TransmissionContinuously Variable Transmission (CVT) with clutch enclosure
Final driveTwo speed, oil bath
Four wheel driveOn-demand true four-wheel drive system
Traction assistPositive locking, mechanically actuated (hand-operated)
Descent controlYes
Suspension
FrontFully independent dual A-Arm with adjustable coils; 7.9 inches (200.7 mm) of travel
RearFully independent dual A-Arm with adjustable coils and sway bar; 9.1 inches (231.14 mm) of travel
Brakes
TypeFront/rear hydraulic disc with twin piston front calipers
Park brakeDriveline, internal wet multi-disc, foot operated (hand release)
Tires / Wheels
Front25x9-12 Terrahawk AT, 27x9-R14 Maxxis Big Horn Radials (on Alloy Rims), or Maxxis Big Horn Radials (on Steel Rims)
Rear25x11-12 Terrahawk AT, 27x11-R14 Maxxis Big Horn Radials (on Alloy Rims), or Maxxis Big Horn Radials (on Steel Rims)
Dimensions / Capacities
Wheelbase2146 mm
84.5 in.
Weight823 kg
1810 lb
With Cab and HVAC: 1019 kg
With Cab and HVAC: 2241 lb
*Additional Attachments and Accessories will add weight
Length3228 mm
127 in.
Width1618 mm
63.7 in.
With doors: 1763 mm
With doors: 69.4 in.
Height1981 mm
78 in.
With roof: 1987 mm
With roof: 78.25 in.
Tread centersFront: 1341 mm
Front: 52.8 in.
Rear: 1259 mm
Rear: 49.6 in.
Ground clearance284 mm
11.2 in.
Fuel capacity42.4 L
11.2 U.S. gal.
Cargo box dimensions1143 x 304.8 x 1320 mm
45 x 12 x 52 in.
Cargo box capacity (weight)454 kg
1000 lb
Payload capacity680 kg
1500 lb
Towing capacity907 kg
2000 lb
HitchStandard 2-in. receiver
Features
ColorGreen/Yellow, Camouflage, Olive and Black
Power steeringNo on E Trim; Yes on M and R Trim
Battery / Alternator / Power port480 CCA 85 amp @ 6000 rpm, regulated, 1020 watts
InstrumentationDigital Display (system diagnostic light, speed, rpm, 4WD indicator, fuel level, coolant temperature, hour meter, miles, park brake light)
StorageFour cup holders (two additional for cab units), in dash, under seat (56.69 L), glove box (3.85 L), optional under hood - except for HVAC units or units with the dealer installed heater kit
SeatingBench (Available Bucket Seats on E and M Trim)

Offers and Discounts

Studio image of XUV 835r

No Interest if Paid in Full within 12 Months1

on New Gator Utility Vehicles

  • No Interest if Paid in Full within 12 Months1
  • Offer available 03 August 2022 through 28 October 2022
Studio image of XUV 835E Gator

0% fixed rate for 36 months1,2

on New Gator XUV or HPX Utility Vehicles

  • 0% fixed rate for 36 months1,2 OR
  • 1.9% fixed rate for 48 months3,4
  • Offers available 03 August 2022 through28 October 2022

1Offer valid on qualifying purchases made between 03 August 2022 to 28 October 2022. This offer excludes TX Turf Gators™ and ProGators. Subject to approved credit on a Revolving Plan account, a service of John Deere Financial, f.s.b. For consumer use only. No down payment required. Interest will be charged to your account from the purchase date at 17.9% APR if the purchase balance is not paid in full within 12 months or if your account is otherwise in default. Available at participating U.S. dealers. Prices and models may vary by dealer. Offer available on new equipment and in the U.S. only. Prices and savings in U.S. dollars.

1Offer valid on qualifying purchases made between 03 August 2022 to 28 October 2022. Subject to approved credit on a Revolving Plan account, a service of John Deere Financial, f.s.b. For consumer use only. No down payment required. 0% APR is for 36 months only, regular Revolving Plan rates will apply after that. The regular Revolving Plan rate, which varies over time, is currently 18.5% APR. Available at participating U.S. dealers. Prices and models may vary by dealer. Offer available on new equipment and in the U.S. only. Prices and savings in U.S. dollars.

2Offer valid on qualifying purchases made between 03 August 2022 to 28 October 2022. Subject to approved installment credit with John Deere Financial, for consumer and Ag use only. Down payment may be required. Average down payment is 10%. $20.83 per month for every $1,000 financed. 0% APR for 36 months only. Taxes, freight, setup, insurance, fees, and delivery charges could increase monthly payment. Available at participating U.S. dealers. Prices and models may vary by dealer. Offer available on new equipment and in the U.S. only. Prices and savings in U.S. dollars.

3Offer valid on qualifying purchases made between 03 August 2022 to 28 October 2022. Subject to approved credit on a Revolving Plan account, a service of John Deere Financial, f.s.b. For consumer use only. No down payment required. 1.9% APR is for 48 months only, regular Revolving Plan rates will apply after that. The regular Revolving Plan rate, which varies over time, is currently 18.5% APR. Available at participating U.S. dealers. Prices and models may vary by dealer. Offer available on new equipment and in the U.S. only. Prices and savings in U.S. dollars.

4Offer valid on qualifying purchases made between 03 August 2022 to 28 October 2022. Subject to approved installment credit with John Deere Financial, for consumer and Ag use only. Down payment may be required. Average down payment is 10%. $17.48 per month for every $1,000 financed. 1.9% APR for 48 months only. Taxes, freight, setup, insurance, fees, and delivery charges could increase monthly payment. Available at participating U.S. dealers. Prices and models may vary by dealer. Offer available on new equipment and in the U.S. only. Prices and savings in U.S. dollars.

Accessories and Attachments

Ag Management Solutions

StarFire™ 3000 Receiver installed on XUV835R StarFire™ 3000 Receiver installed on XUV835R
GreenStar™ display installed on XUV835R with optional phone and tablet mounts GreenStar™ display installed on XUV835R with optional phone and tablet mounts

The AMS integration kit allows the operator to mount a StarFire Receiver and GreenStar display (both receiver and display sold separately) to the Gator™ Utility Vehicle.

 

Key features of the AMS integration kit:

  • Compatible with StarFire iTC, StarFire 3000, and StarFire 6000 Receivers
  • Compatible with GreenStar 2 1800, GreenStar 2 2600, GreenStar 3 2630, and John Deere 4640 Universal Display
  • Ability to mount receiver to the poly roof or on the occupant protective structure (OPS) alone

 

NOTE: Additional components are required to support the John Deere 4640 Universal Display include:

  • AL212683 (1)
  • 21M7577 (2)

 

Common applications:

  • Boundary mapping
  • Flagging field obstacles
  • Soil sampling

 

Compatibility:

  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles

 

Electrical harness requirements:

 XUV835/865   Attachment harness required (see below)
 E 1, 3, 5, 6
M (open station) 3, 5, 6
M (cab, factory installed) 5, 6
R 6
 1  E-spec attachment harness
 2  Front attachment harness
 3  Roof attachments harness
 4  Front cab harness
 5  Rear cab harness
 6  Dash port harness
 Code Attachment Description
  BUC10634 AMS integration kit

AMS Integration Kit - 57KAMBUC11510

Backup Alarm

Cargo Box

Cargo box pail holder Cargo box pail holder
Cargo box pail holder Cargo box pail holder

The 5-gal. (18.9-L) pail holder is ideal for operators who want to maximize the work capability of their Gator™ Utility Vehicle. The 5-gal. (18.9-L) pail holder keeps pails in place within the cargo box, ensuring that they stay safe and secure. Featuring the quick-clamp mounting system, it mounts easily to the cargo rails of the cargo box with just one clamp.

Cargo bed extender Cargo bed extender
Cargo bed extender Cargo bed extender

The cargo bed extender conveniently extends the rear of the cargo bed, and also acts as a cargo box divider when it is flipped inside of the cargo box. The cargo bed extender easily flips in or out with the use of quick-pull pins.

Deluxe cargo box bed mat Deluxe cargo box bed mat

The deluxe cargo box bed mat not only protects the steel floor from scratches and dents, it also provides additional cushioning and slip resistance to items being hauled in the cargo box.

Cargo box divider located at rear of cargo bed Cargo box divider located at rear of cargo bed
Cargo box divider located at front of cargo bed Cargo box divider located at front of cargo bed
Speedrail lock in the unlocked position Speedrail lock in the unlocked position
Speedrail lock in the locked position Speedrail lock in the locked position

The Gator™ XUV Series can be equipped with an optional divider for the deluxe cargo box. The dividers can be positioned at the front or rear of the cargo box bed. To change positions of the dividers, simply release the speedrail locks by hand and slide into new position, then close the locks to secure the dividers.

Cargo box side extension kit Cargo box side extension kit
#

The cargo box side extension kit expands the versatility of the Gator™ Utility Vehicles and is ideal for those who are enhancing their property and landscape. The extensions allow operators to haul twice the volume (not to exceed cargo box weight capacity) of light material such as grass clippings and mulch. 

 

Product features include:

  • Four-sided structure that increases cargo box side height to 533 mm (21 in.) and volume to 0.74 m3 (26 cu ft)
  • Mounted on the sides and front with hardware, while the tailgate can be attached or removed without tools
    • Tailgate pivots at the top (similar to a dump truck) for ease of dumping loose material
  • Laser-cut, heavy-gauge, powdered-coated steel provides excellent durability
  • Compatible with all model year 2011 to current Gator XUV625i, XUV825i, XUV825i S4, XUV855D, XUV855D S4, and M-Gator A2 Utility Vehicles
  • Compatible with model year 2010 to current Gator TX 4X2, TH 6X4 Gas, TH 6X4 Diesel, TE, and TX Turf Utility Vehicles
  • Compatible with model year 2018 and newer gas and diesel HPX Utility Vehicles.
  • Compatible with Gator cabs and bedliner

 

NOTE: The cargo box side extensions are not intended to increase the rated cargo box carrying capacity per the vehicle specification.

Rear fender flare kit on XUV865 Rear fender flare kit on XUV865
Rear fender flare kit Rear fender flare kit

A – Fender flare

B – Fender

 

The rear fender flare kit minimizes debris from reaching the operator station.

Product features include:

  • Two pliable fender flares (one for each side)
  • Hardware for mounting on the sides
  • Compatible with all model year 2011 to current Gator™ XUV825, XUV825 S4, XUV855, XUV855 S4, XUV835, and XUV865 Utility Vehicles
  • Compatible with model year 2010 to current Gator TX 4X2, TH 6X4 Gas, TH 6X4 Diesel, TE, and TX Turf Utility Vehicles
  • Compatible with model year 2018 and newer gas and diesel HPX Utility Vehicles
Rear fender flare Rear fender flare
Overview

Rear fender flares reduce mud and debris splashing onto the vehicle and passengers. The flares are constructed from a durable molded material and integrated into the cargo box fenders. The attachment kit includes a pair of flares and mounting hardware.

Compatibility

XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, XUV865R vehicles. Signature Edition vehicles include rear fender flares in base equipment.

Tool rack Tool rack
Tool rack with tools Tool rack with tools

The side tool rack enables the user to maximize the use of their cargo box by carrying long-handled tools, such as trimmers, shovels, and rakes, on the outside of the box. The holders are adjustable, allowing the users to carry a wide array of items in the racks.

Tool rack holder detail Tool rack holder detail
Adjusting the tool rack holder Adjusting the tool rack holder
Spare tire carrier Spare tire carrier
Spare tire carrier Spare tire carrier

Easily mount a spare tire to the side of the cargo box with this convenient kit.

 

Recommended to carry spare front tire, as the front tire can be mounted on either the front or rear hubs.

Cargo Box Lift

Cargo box power lift kit shown in full up position Cargo box power lift kit shown in full up position
Overview

The Gator™ utility vehicles can be equipped with an optional power lift for the cargo box. This is one of the most important accessories for increasing work efficiency. It is an excellent complement to these highly capable utility vehicles.

Benefits
  • Capable of lifting a maximum vehicle cargo box load of 454 kg (1000 lb)
  • Lifts box to 49 degrees from horizontal for ease of service and cargo box load removal
  • Quick horizontal-to-49-degree time
  • Can be installed in minutes using the vehicle's prewired connectors and mounting points
  • Compact design fits nicely around the transmission and linkages, providing full protection
  • Fully sealed and weatherproof design does not require maintenance and is built for maximum durability
  • Overload protection protects against misuse

Cover

High-performance sport seat cover - black High-performance sport seat cover - black
High-performance sport seat cover - camo High-performance sport seat cover - camo
High-performance sport seat cover - coyote High-performance sport seat cover - coyote

Each kit (available through Order Zone) contains one bench base cover, one backrest cover, and installation instructions.

 

NOTE: One carton (two kits) outfits driver and passenger seats.

 

Special features:

  • Exceptional abrasion, tear, and puncture resistance
  • Constructed with military-grade CORDURA® fabrics
  • Protects original equipment manufacturer (OEM) seats from mud, snow, and debris
  • Quick and easy installation
  • Available in black or Realtree Hardwoods HD® pattern
  • Military-grade zippers
  • Limited 1-year warranty
  • Made in the USA

 

Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd. CORDURA is a trademark of INVISTA North America, LLC.

High-performance sport seat cover - black High-performance sport seat cover - black
High-performance sport seat cover - camo High-performance sport seat cover - camo
High-performance sport seat cover - coyote High-performance sport seat cover - coyote

Each kit (available through Order Zone) contains one bench base cover, one backrest cover, and installation instructions.

 

NOTE: One carton (two kits) outfits driver and passenger seats.

 

Special features:

  • Exceptional abrasion, tear, and puncture resistance
  • Constructed with military-grade CORDURA® fabrics
  • Protects original equipment manufacturer (OEM) seats from mud, snow, and debris
  • Quick and easy installation
  • Available in black or Realtree Hardwoods HD® pattern
  • Military-grade zippers
  • Limited 1-year warranty
  • Made in the USA

 

Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd. CORDURA is a trademark of INVISTA North America, LLC.

High-performance sport seat cover - black High-performance sport seat cover - black
High-performance sport seat cover - camo High-performance sport seat cover - camo
High-performance sport seat cover - coyote High-performance sport seat cover - coyote

Each kit (available through Order Zone) contains one bench base cover, one backrest cover, and installation instructions.

 

NOTE: One carton (two kits) outfits driver and passenger seats.

 

Special features:

  • Exceptional abrasion, tear, and puncture resistance
  • Constructed with military-grade CORDURA® fabrics
  • Protects original equipment manufacturer (OEM) seats from mud, snow, and debris
  • Quick and easy installation
  • Available in black or Realtree Hardwoods HD® pattern
  • Military-grade zippers
  • Limited 1-year warranty
  • Made in the USA

 

Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd. CORDURA is a trademark of INVISTA North America, LLC.

ROPS, KIT, ENCORE - 57KAMBUC11640

Vehicle storage cover Vehicle storage cover
Vehicle storage cover Vehicle storage cover
Key features
  • All-season protection against sun damage, rain, dust, and tree sap
  • Reinforced corners for added durability
  • Fabric coated for maximum water resistance and repellency
  • Elastic shock cord in bottom hem for a quick, custom fit

 

Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Ordering information

Available through Order Zone

Drawbar

Floor Mat

Left floor mat Left floor mat
Right floor mat Right floor mat
Key features
  • Kit includes left and right floor mats
  • Made from 8-mm (5/16-in.) thick textured rubber
  • Tool-less install and easy removal for cleaning
  • Helps further dampen operator station noise
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Front Rack

Hood rack Hood rack
Hood rack (hinged forward) Hood rack (hinged forward)
Key features
  • 124.5-cm (49-in.) long x 36-cm (14.25-in.) wide x 11-cm (4.25-in.) deep
  • Welded steel tubing
  • Design allows for convenient tie-down points to secure load
  • 45-kg (100-lb) capacity
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles
  • Requires brush guard to be installed

Guards

Brush guard Brush guard
Quick pull pins Quick pull pins
Brush guard hinged forward Brush guard hinged forward
Auxiliary lights mounted on brush guard (sold separately) Auxiliary lights mounted on brush guard (sold separately)
Key features
  • Provides a modern and aggressive appearance
  • Heavy-duty, 44.45-mm (1.75-in.) diameter, steel tube construction
  • Welded steel brush guard provides protection for the front grille, lights, and hood
  • Easy-to-use quick pull pins allow the brush guard to be hinged forward to gain access under the hood
  • Includes mounts for auxiliary light-emitting diode (LED) lights (sold separately)
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Brush guard extensions Brush guard extensions
Brush guard extensions Brush guard extensions
Brush guard with extensions hinged forward Brush guard with extensions hinged forward
Brush guard with extensions Brush guard with extensions
Key features
  • Enhances the aggressive appearance of the vehicle
  • Easily attaches to the brush guard (required – sold separately)
  • Provides additional protection to the side hood and fender area without adding additional overall width to the vehicle
  • Still allows full entry under the hood when brush guard is hinged forward
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Cargo Box Fender Guard - 57KAMBUC11320

Front CV guards Front CV guards
Rear CV guards Rear CV guards
Key features
  • Kit contains both front and rear CV guards
  • Additional added protection for the A-arms and CV joints
  • High-strength, formed steel guards handle impacts while maintaining a low, unsprung mass to provide exceptional ride quality
  • Easily bolts to the A-arms
  • Drainage holes on the bottom of the guards prevent buildup of dirt, grass, and other loose materials
Compatibility
  • Model year 2020 and newer XUV835 and XUV865 Utility Vehicles
Front fender guards - shown with brush guard (required) and brush guard extensions (optional) Front fender guards - shown with brush guard (required) and brush guard extensions (optional)
Key features
  • Easily attaches to the brush guard (required – sold separately)
  • Provides protection to the front fender area
    • NOTE: With fender guards installed, the overall width of the vehicle increases to 1.75 m (69 in.).

 

Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Rear bumper kit (TH 6X4 shown) Rear bumper kit (TH 6X4 shown)

The rear bumper offers stylish, heavy-duty rear protection to the vehicle.

Compatible with:

  • Model year 2011 and later Gator™ XUV 625i, XUV 825, and XUV 855 Utility Vehicles
  • Model year 2010 and later Gator TX, TX Turf, TH 6X4 Gas, TH 6X4 Diesel, and TE Utility Vehicles
  • Model year 2018 and later Gator XUV835 and XUV865 Utility Vehicles
Rear CV guards Rear CV guards

CV guards add additional protection for the A-arms, brake lines, and CV half shafts:

 

  • Formed steel guards handle impacts while maintaining a low unsprung mass
  • Easily bolt to the A-arms with six bolts
  • Drainage holes provided to prevent buildup of dirt, grass, and other loose materials
  • Compatible with all model year 2011 to current Gator™ XUV625i, XUV825, XUV855, and M-Gator A2 Utility Vehicles
  • Compatible with model year 2013 to current Gator XUV825 S4 and XUV855 S4 Utility Vehicles
  • Compatible with model year 2018 to current Gator XUV835 and XUV865 Utility Vehicles
Rear-panel glass protector Rear-panel glass protector
Key features
  • Provides protection to the cab rear-panel glass
    • NOTE: Never carry loads in the cargo box over the load guard.
  • Perforated, black metal screen easily attaches to the cab rear panel (required – sold separately)
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Brake and taillight protector Brake and taillight protector

The brake and taillight protector offers increased protection to the taillight assembly from incidental contact.

Harnesses

CAN Bridge Control Kit - 57KAMBUC10811

Front attachment harness Front attachment harness

The front attachment harness includes connections for the following kits:

  • Light-emitting diode (LED) headlights
  • Turn signals
  • Horn
  • Brush-guard-mounted auxiliary lights
Dash port harness connection Dash port harness connection
Dash port harness – lower connectors Dash port harness – lower connectors
Key features
  • The front attachment harness (dash port) includes connections for the following kits:
    • Rear sprayer
    • Rear spreader
    • Blades
    • GreenStar™ Display as part of the Ag Management Solutions (AMS) integration kit
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Hydraulic blade and rear winch harness Hydraulic blade and rear winch harness

Key features:

  • The hydraulic blade and winch harness includes connections for the following kits:
    • Hydraulic blade
    • Winch

 

Compatibility:

  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Rear cab attachment harness Rear cab attachment harness
Key features
  • The rear cab attachment harness includes connections for the following kits:
    • Rear auxiliary lights
    • Beacon light
    • Ag Management Solutions (AMS) receiver harness
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Horn

Horn Horn
Horn switch Horn switch
Key features
  • Frequency: 410 Hz
  • Sound pressure level: 100+ dB(A)
  • Water-sealed type
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Electrical harness requirements
XUV835/865  Attachment harness required (see below) 
 E  1, 2
 M (open station)  2
 M (cab, factory installed)  2
 R  ---

 

E-spec attachment harness 
2 Front attachment harness
Roof attachments harness
Front cab harness 
Rear cab harness 
Dash port harness 

Lighting

Beacon light in up position Beacon light in up position
Beacon light in down position Beacon light in down position
Backlit beacon light switch Backlit beacon light switch
Key features
  • 76-mm (3-in.) round, light-emitting diode (LED) strobe light provides excellent visibility for vehicle bystanders
  • Especially useful for working around properties and job sites
  • Acrylic amber lens resists scratching and scuffing
  • Impact-resistant nylon housing
  • Society of Automotive Engineers (SAE) J845 (Class 3)-compliant
  • UL® recognized
  • Flash rate: 60 +/- 10 fpm
  • Stands 21.3-cm (8.4-in.) tall from roof/occupant protective structure (OPS)
  • Folds down out the way when not in use
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Electrical harness requirements
XUV835/865  Attachment harness required (see below) 
 E  1, 3, 5
 M (open station)  3, 5
 M (cab, factory installed)  5
 R  ---

 

E-spec attachment harness 
2 Front attachment harness
Roof attachments harness
Front cab harness 
Rear cab harness 
Dash port harness 

 

UL is a trademark of UL LLC.

LED headlights LED headlights
Three-position backlit light switch Three-position backlit light switch
Key features
  • Upgrade from halogen headlights
  • High/low beam
  • Raw lumen output (per light): 1,075 (high beam), 430 (low beam)
  • Effective lumen output (per light): 720 (high beam), 240 (low beam)
  • Nominal LED color temperature: 5000 K
  • Current draw: 1.14 amps (high beam), 0.41 amps (low beam)
Compatibility
  • Model year 2018 and newer XUV835 and XUV865 Utility Vehicles
  • Model year 2021 and newer XUV560E, XUV560E S4, XUV590E, XUV590E S4, XUV590M, and XUV590M S4 Utility Vehicles
Electrical harness requirements
XUV835/XUV865  Attachment harness required (see below) 
 E  1, 2
 M (open station)  2
 M (cab, factory installed)  2

 

E-spec attachment harness 
2 Front attachment harness
Roof attachments harness
Front cab harness 
Rear cab harness 
Dash port harness 
Front cab mounted Front cab mounted
Rear cab mounted Rear cab mounted
Brush guard mounted Brush guard mounted
Key features
  • The LED driving lights can be mounted on the front occupant protective structure (OPS), front cab, rear OPS, rear cab, or brush guard
  • Beam pattern: driving (focused, intense beam of light good for illuminating a stretch of road directly in front of the vehicle)
Driving beam pattern – mounted on brush guard Driving beam pattern – mounted on brush guard
Driving beam pattern – mounted on OPS/roof Driving beam pattern – mounted on OPS/roof
  • Lamp sealing: IP69K
  • Light output (per light): 1150 lumens
  • LED color temperature: 5000 K
  • Amp draw (per light): 1.4 amps
  • 6 LEDs per light
  • Aluminum housing
Compatibility
  • Model year 2011 to current XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles
  • Model year 2012 to current XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles
  • HPX Utility Vehicles

LED Single Beam Headlights - 57KAMBUC10876

Front cab mounted Front cab mounted
Rear cab mounted Rear cab mounted
Brush guard mounted Brush guard mounted
Key features
  • The LED work lights can be mounted on the front occupant protective structure (OPS), front cab, rear OPS, rear cab, or brush guard
  • Beam pattern: flood (spread of light over a wider, shorter distance)
Flood beam pattern – mounted on OPS/roof Flood beam pattern – mounted on OPS/roof
  • Lamp sealing: IP69K
  • Light output (per light): 1200 lumens
  • LED color temperature: 5000 K
  • Amp draw (per light): 1.4 amps
  • 6 LEDs per light
  • Aluminum housing
Compatibility
  • Model Year 2011 to current XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles
  • Model Year 2018 to current XUV835 and XUV865 Utility Vehicles
  • Model Year 2012 to current XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles
  • HPX Utility Vehicles

Mirrors

Rearview mirror Rearview mirror
Key features
  • Convex mirror reflects a wide-angle image to help the operator see behind the vehicle
  • Connected to ball stud for easy adjustment
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Side mirrors – open station Side mirrors – open station
Side mirrors – open station Side mirrors – open station
Side mirrors – cab door Side mirrors – cab door
Side mirrors – cab door Side mirrors – cab door
Key features
  • Kit allows mirrors to be installed on either an open-station or cab vehicle
  • Mirrors can be easily adjusted based on operator preference
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Side Mirrors (open station & cab doors) - 57KAMBUC11227

Operator's Station

Accessory mounting bracket (shown with tablet and cell phone mount) Accessory mounting bracket (shown with tablet and cell phone mount)
Key features
  • Allows the cell phone and tablet mount to be installed in the upper dash location
  • Required for cell phone mount if mounted in the lower dash location
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Cell phones, global positioning system (GPS), and other devices are key tools for farming today. John Deere has now made it easier than ever to incorporate these tools into the operator station.

RAM X-Grip holder RAM X-Grip holder

For proper machine operation, it is critical that accessory devices and tools be located and mounted where they are accessible but do not interfere with visibility and controls. The new RAM® mount kit has been specially developed to meet this need in John Deere tractors and now utility vehicles.

 

Simply remove the large wing nut from the assembly, insert the stud into any open hole in the occupant protective structure (OPS), and tighten down the jam nut.

Key benefits:

  • Patented RAM X-Grip™ holder fits most cell phones and similar devices including iPod®, iPad®, iPhone®, BlackBerry®, Samsung Galaxy® and others.
  • Mounts to the holes in the OPS
  • Ball joints allow for variable positioning
  • Holds firm even in rugged terrain
  • The holder is compatible with many other RAM® products with their B size or 25.4-mm (1-in.) ball accessories
RAM X-Grip RAM X-Grip

The RAM X-Grip has a clean and clever four-leg design that sports great holding power without hiding the phone behind foam pads and plastic.

 

Features:

  • Rustproof
  • High-strength composite and stainless-steel construction
  • Spring-loaded holder expands and contracts for custom fit
    • Minimum width: 1.875 in. (47 mm)
    • Maximum width: 3.25 in. (82 mm)
    • Depth: 0.875 in. (22 mm)
  • Rubber-coated tips will hold device firm and stable
  • Easy access grip knobs for quick release of your device

 

Warranty:

90 days, limited.

 

RAM and RAM X-Grip are trademarks of National Products Inc. iPad, iPod, and iPhone are trademarks of Apple, Inc. BlackBerry is a trademark of Research In Motion Limited (RIM). Samsung Galaxy is a trademark of  Samsung Electronics Co.

Visors (shown on R-spec) Visors (shown on R-spec)
Visors (shown on R-spec) Visors (shown on R-spec)
Key features
  • Shades occupants from the glare of sunlight
  • Hinged design
  • Tan color
  • Kit includes left and right visor. Rearview mirror kit required for installation.
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Tablet mount – upper mount location  (shown with cell phone mount – sold separately) Tablet mount – upper mount location (shown with cell phone mount – sold separately)
Tablet mount – lower mount location (shown with cell phone mount – sold separately) Tablet mount – lower mount location (shown with cell phone mount – sold separately)
Key features
  • Keeps tablet at the operator’s fingertips for doing jobs such as soil sampling
  • Utilizes a RAM® mount to easily move tablet to desired location
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles


RAM is a trademark of National Products, Inc.

Radio

Upper speakers Upper speakers
Subwoofer Subwoofer
Bluetooth® microphone Bluetooth® microphone
SiriusXM® Radio antenna/tuner SiriusXM® Radio antenna/tuner
Key features
  • Kit includes:
    • Wiring harnesses
    • SiriusXM® radio antenna/tuner (XM ready head unit required – sold separately)
    • Two 13.3-cm (5.25-in.) upper speakers
    • Subwoofer
    • Bluetooth® wireless microphone
  • Jensen® speakers
    • Waterproof
    • 45-W root mean square (RMS) power each
    • 135-W peak power each
  • Jensen subwoofer
    • Waterproof
    • 20.3-cm (8-in.) amplified subwoofer
    • Maximum power: 200 W
    • Aluminum mesh grille
    • Aluminum housing
  • The head unit is sold separately through Parts. The operator must choose one of the following two head units to complete the stereo:
    • SWJHD1635BT – heavy-duty stereo with AM/FM, weatherband, auxiliary input, SiriusXM satellite radio, and Bluetooth technology
    • SWJHD36AMIC – heavy-duty stereo with AM/FM, weatherband, compact disc (CD), auxiliary input, SiriusXM satellite radio, USB 2.0, and Bluetooth technology

NOTE: Must order head unit through Parts.

Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles
  • Requires base radio kit

 

SiriusXM is a trademark of Sirius XM Radio Inc. Bluetooth is a trademark of Bluetooth SIG, Inc. Jensen is a trademark of Electronics Trademark Holding Company LLC.

Lower left speaker Lower left speaker
Lower right speaker Lower right speaker
Head unit (sold separately) installed Head unit (sold separately) installed
Key features
  • Kit includes:
    • Wiring harness
    • AM/FM antenna
    • Head unit mounting bracket
    • Two 13.3-cm (5.25-in.) speakers
  • Jensen® speakers
    • Waterproof
    • 45-W root mean square (RMS) power each
    • 135-W peak power each
  • The head unit is sold separately through Parts. The operator must choose one of the following three head units to complete the stereo:
    • SWJHD1130 – heavy-duty stereo with AM/FM, weatherband, and auxiliary input
    • SWJHD1635BT – heavy-duty stereo with AM/FM, weatherband, auxiliary input, SiriusXM® satellite radio, and Bluetooth® wireless technology
      • NOTE: To complete the SiriusXM system, please order SWR169159 antenna and SWSXV200B tuner.
    • SWJHD36AMIC – heavy-duty stereo with AM/FM, weatherband, compact disc (CD), auxiliary input, SiriusXM satellite radio, USB 2.0, and Bluetooth wireless technology
      • NOTE: To complete the SiriusXM system, please order SWR169159 antenna and SWSXV200B tuner.

NOTE: Must order head unit through Parts.

Compatibility
  • Model year 2018 and newer XUV835 and XUV865 Utility Vehicles

Jensen is a trademark of Electronics Trademark Holding Company LLC. SiriusXM is a trademark of Sirius XM Radio Inc. Bluetooth is a trademark of Bluetooth SIG, Inc.

Roof

Roof headliner Roof headliner
Roof headliner installation Roof headliner installation
Key features
  • Enhances the appearance of the operator station with a molded, soft-touch, automotive-style roof headliner
  • Made from 3.175-mm (1/8-in.) thick sound-dampening material for improved occupant comfort
  • Easily attaches to the roof with cap screws and push darts
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Seat

Bench seat cover (shown in black) Bench seat cover (shown in black)
Modular lightweight load-carrying equipment (MOLLE) attachment location Modular lightweight load-carrying equipment (MOLLE) attachment location
Overview

Bench seat covers are available for full-size Gator™ utility vehicles.

Benefits
  • Protection for the bench seat from wear and stains
  • Constructed with military-grade CORDURA® fabrics
  • Quick and easy installation
  • MOLLE attachment locations (MOLLE attachments available through Order Zone)
  • Easy access to seatbelts
  • Available in three color options: black, Realtree EDGE® camo, or coyote brown
Additional details

Compatibility

  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles

 

Ordering information

Available through Order Zone.

 

CORDURA is a trademark of INVISTA North America, LLC. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

Bench seat cover (shown in black) Bench seat cover (shown in black)
Modular lightweight load-carrying equipment (MOLLE) attachment location Modular lightweight load-carrying equipment (MOLLE) attachment location
Overview

Bench seat covers are available for full-size Gator™ utility vehicles.

Benefits
  • Protection for the bench seat from wear and stains
  • Constructed with military-grade CORDURA® fabrics
  • Quick and easy installation
  • MOLLE attachment locations (MOLLE attachments available through Order Zone)
  • Easy access to seatbelts
  • Available in three color options: black, Realtree EDGE® camo, or coyote brown
Additional details

Compatibility

  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles

 

Ordering information

Available through Order Zone.

 

CORDURA is a trademark of INVISTA North America, LLC. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

Bench seat cover Bench seat cover
Key features
  • Protection for the bench seat from wear and stains
  • Elastic-hem cord closure for easy adjustment
  • Easy access to seatbelts
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Ordering information

Available through Order Zone

Bench seat cover (shown in black) Bench seat cover (shown in black)
Modular lightweight load-carrying equipment (MOLLE) attachment location Modular lightweight load-carrying equipment (MOLLE) attachment location
Overview

Bench seat covers are available for full-size Gator™ utility vehicles.

Benefits
  • Protection for the bench seat from wear and stains
  • Constructed with military-grade CORDURA® fabrics
  • Quick and easy installation
  • MOLLE attachment locations (MOLLE attachments available through Order Zone)
  • Easy access to seatbelts
  • Available in three color options: black, Realtree EDGE® camo, or coyote brown
Additional details

Compatibility

  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles

 

Ordering information

Available through Order Zone.

 

CORDURA is a trademark of INVISTA North America, LLC. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

Comfort straps Comfort straps

Kit includes two comfort straps for the left and right seat belts.

  • Provides relief to the operator's and passenger's upper body when driving over rough terrain by allowing the seat belt to stretch when the seat belt locks
  • Moves the upper mounting point of the seat belt down 6 in. (152 mm)
  • Can be mounted to both the driver- and passenger-side upper mounting point of the three-point seat belt
  • Compatible with all model year 2017 - current Gator™ HPX, XUV625i, XUV825i, XUV825i S4, XUV855D, XUV855D S4, XUV560, XUV560 S4, XUV590i, XUV590i S4, and RSX860i Utility Vehicles when equipped with standard Occupant Protective Structure (OPS)
  • Compatible only with standard Occupant Protective Structure (OPS), for deluxe cab frame, order BM22703

Spacers

Wheel spacer kit Wheel spacer kit
This wheel spacer kit is available for use on X729, X739, and X749 Tractors and model year 2018 and newer XUV835 and XUV865 Utility Vehicles. Overall machine width at the wheels is increased by 2 in. (51 mm) with the wheel spacer kit.

Use on utility vehicles
The additional space provided on utility vehicles allows for more comfortable operation between 30-in. (762-mm) rows. Spacers simply bolt to the axle hub and the wheels to the spacer.

NOTE: Wheel spacers are only compatible with steel wheels without the center caps installed.

Use on tractors
Use the wheel spacer kit for tractors when installing tire chains with the standard 26x12-12 heavy-duty all-purpose (HDAP) tires and for all four-wheel steer (4WS) tractors using the LP39859 TerraGrip traction belts (pair) on 26x10.5-12 tires:
  • The wider 26x12-12 tires, used in combination with four-wheel steering, on the X729, X739, and X749 Tractors do not allow adequate clearance for the tire chains, so the wheel spacer kit is required.
  • Spacers simply bolt to the axle hub and the wheels to the spacer.
  • BM22725 may also be used in all applications where the BM18021 wheel spacer kit has been used.
  • BM22725 has additional hardware and an updated operator's manual compared to the BM18021 wheel spacer kit.
    • BM18021 was developed for use on the 400 Series (425, 445, and 455) Four-Wheel Steer Tractors for installing tire chains on the 4WS models when using 23x10.50-12 rear tires.
  • The wheel spacer kit must be removed for use with the 54-in. (137-cm) Mower Deck on X700 Tractors.

Wheel spacer kit - 57KAMBUC11452

Sprayers

45-gal. (170-L) Gator bed sprayer 45-gal. (170-L) Gator bed sprayer
#

The 45-gal. (170-L) Gator bed sprayer is designed to work with the Gator vehicles equipped with the steel bed or deluxe cargo box. It provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. It comes complete with a 43-in. boom that sprays a 120-in. swath. It's equipped with a 20-ft hose and a spray wand for spot spraying lawns, shrubs, trees, etc. The fully adjustable brass spray wand tip achieves streams up to 30 ft. It comes equipped with rubber feet and custom brackets, which secure to the Gator bed, for a no tools mount.

 

Special features:

  • 45-gal. (170-L) capacity
  • Brackets secure to Gator bed, no tools or additional strapping required after initial set-up
  • Brackets allow boom height adjustment
  • 100 psi SHURflo diaphragm-type pump is designed for high hour commercial applications. It can be run dry without damage
  • The fully adjustable brass spray wand tip achieves streams up to 30 ft
  • Equipped with a 20-ft hand wand hose with side mount hose tender for convenience
  • Check valves in boom tips prevent siphoning and dripping, which can cause lawn spotting
  • On/off switch located near operator
  • Easy boom removal for added convenience
  • Control valve channels spray to either the boom or spray wand
  • 12-V plug included with wiring harness, complete with quick-disconnects, for convenient electrical hookup
  • Rugged translucent yellow tank with molded fill level indicators (in gallons)
Specifications

Capacity

45 U.S. gal. (170 L)

Pump

Type

Electric motor and diaphragm

Manufacturer

SHURflo® 

Operating pressure

100 psi

Current draw

7 amp

Valve material

Viton® 

Diaphragm material

Santoprene™

Spray flow rate

2.1 U.S. gpm (8 L/min)

Sump strainer

Stainless steel

Remote spray method

Spray wand

Polypropylene with Viton components

Tip material

Brass

Adjustment Fan-to-stream
Hose length 20-ft nylon reinforced rubber

Boom

Boom width 43-in. (109 cm) fixed
Spray swath 120-in. (305 cm)
Spray tip(s) Three - TF-VP3

Mounting

Steel bed Custom tailgate clamp mounting
Deluxe cargo box Custom brackets secure to tie-downs

Compatibility

All Gator models except CX

Shipping weight

68 lb (31 kg)

Net weight

64 lb (29 kg)

 

Ordering information

Contact the local John Deere dealer for availability and pricing information.

 

45-gal. (170-L) Gator bed sprayer
Order number: LP20852

 

SHURflo is a U.S.-registered trademark of Sta-Rite Industries, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.

High-performance 45-gal. (170-L) Gator bed sprayer High-performance 45-gal. (170-L) Gator bed sprayer
#

The high-performance Gator bed sprayer is designed to work with Gator vehicles equipped with the deluxe cargo box or steel bed. With a 45-gal. (170-L) capacity, high volume electric pump, and premium pistol grip spray gun, it provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray and de-icer. Engineered brackets secure the sprayer to the Gator bed with no tools, or additional tie-downs required.

NOTE: Sprayer shown above with optional 150-in. precision boom (LP22885).

High-performance features:

  • 45 psi, 3.6 gpm SHURflo® diaphragm-type pump is designed for high hour applications and can be run dry without damage
  • Premium pistol grip spray gun, designed for single hand mist to 35-ft stream
  • Equipped with a 20-ft hand wand hose with side mount hose tender for convenience
  • Glycerin-filled pressure gauge and TeeJet™ pressure regulation/recirculation valve
  • Choice of booms (sold separately)
  • On/off capabilities in the palm of your hand with the included sprayer remote control (LP22912)
  • 12V plug included with wiring harness, complete with quick-disconnects, for convenient electrical hookup
  • Brackets secure to Gator bed, no tools or additional strapping required after initial set-up
  • Control valve channels spray to either the boom or spray wand
  • Rugged translucent yellow tank with molded fill level indicators (in gallons)
Specifications

Capacity

45 U.S. gal. (170 L)

Pump

Type

Electric motor and diaphragm

Manufacturer

SHURflo® 

Operating pressure

45 psi

Current draw

7 amp

Valve material

Viton® 

Diaphragm material

Santoprene™

Spray flow rate

3.6 U.S. gpm (13.6 L/min)

Sump strainer

Stainless steel

Remote spray method

Spray wand

Poly, alloy, and brass with Viton components

Tip material

Brass and stainless

Adjustment Fan-to-stream
Hose length 20-ft - 1/2-in. nylon reinforced rubber

Gauge

Glycerin filled

Spray control

Pressure regulation/recirculation

Remote control

12V receiver with dual FOB remote on/off

Boom (sold separately)

Option 1 150-in. spray width precision folding (5 tip)
Option 2 120-in. spray width (3 tip)
Option 3 24-ft boomless nozzle

Mounting

Steel bed Custom tailgate clamp mounting
Deluxe cargo box Custom brackets secure to tie-downs

Compatibility

All Gator models (except CX)

Shipping weight

56 lb (25 kg)

Net weight

52 lb (23 kg)

 

Ordering information

Contact the local John Deere dealer for availability and pricing information.

 

High-performance 45-gal. (170-L) Gator bed sprayer
Order number: LP22908

 

SHURflo is a U.S.-registered trademark of Sta-Rite Industries, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.

340.7-L (90-gal.) single tank sprayer 340.7-L (90-gal.) single tank sprayer

The high-performance (HP) single-tank 340.7-L (90-gal.) Gator bed sprayer is designed to work with Gator vehicles equipped with the deluxe cargo box that have a capacity in excess of 362.9 kg (800 lb). The custom molded 340.7-L (90-gal.) tank provides a low profile with capacity perfect for athletic fields, farmettes, commercial maintenance, or any large property. It provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. Custom engineered mounting hardware ensures the unit stays secure without the use of additional straps or tie-downs. Cover ground quickly with flexible boom options. (Boom sold separately).

High-performance features:
  • 100 psi, 4-GPM diaphragm-type pump is designed for high-hour applications and can be run dry without damage
  • Premium pistol grip spray gun, designed for single-hand mist to 10.7-m (35-ft) stream.
  • Side-mount hose tender for easy hose access and storage
  • Glycerin-filled pressure gauge
  • TeeJet™ pressure regulation/recirculation valve for precise sprayer calibration
Additional features:
  • Custom engineered brackets secure to Gator bed with no tools or additional straps
  • Control valve channels spray to either the boom or spray wand
  • Includes Gator accessory wiring harness, complete with quick disconnects, for convenient electrical hookup
  • Rugged translucent yellow tank with molded fill level indicators (in gallons)
340.7-L (90-gal.) sprayer on XUV835 340.7-L (90-gal.) sprayer on XUV835
Overview

The 341-L (90-gal.) rate controlled sprayer for Gator™ utility vehicles is proof that the evolution of modern sprayers is correlated to progress in electronics and forward thinking. By utilizing pulse width modulation (PWM) technology, like the systems found on large-scale ag sprayers, this sprayer provides many of the same features and benefits to operators with XUV835 and XUV865 Full-Size Crossover Utility Vehicles.

Benefits
  • Greater productivity due to faster travel while spraying
  • Easier adjustments through advanced controls using the 8.1-cm (3.2-in.) display
  • Savings on chemical costs thanks to more consistent application rate
  • Lower risk of environmental contamination because of precision spray rate
Additional details

With this sprayer, operators effortlessly maintain their application rate without needing to hold a constant ground speed. For example, if the operator slows down to maneuver around an obstacle, the solenoid valves on the sprayer tips compensate by decreasing the rate of material being applied. If the operator stops the vehicle, the solenoid valves shut the tips off completely and the spray returns to the tank through a return valve. This precise measuring of the Gator utility vehicle’s speed is done through a controller area network (CAN) bridge (BUC10316), which provides instantaneous communication between the sprayer and the vehicle.

For simple operation, an 8.1-cm (3.2-in.) display mounts to the vehicle’s dash. This display allows operators to easily select a spray mode (boom or wand), adjust the speed range, tip size, and flow rate, and individually activate or deactivate tips for more application options. After setup, the minimum and maximum speed ranges are shown as a horizontal meter to help the operator avoid traveling too fast or too slow based on their set parameters.

Partnering with this technology is a proven 20-L/min (5.3-gpm) Shurflo® pump that provides up to 4.1 bar (60 psi). Material is applied as wide as 3.8 m (12.5 ft) with a durable, spring-loaded folding steel boom. Also included is a deluxe hand wand with a brass tip that provides both cone and stream spray patterns. Attached to the wand is 9.1 m (30 ft) of hose that is ideal for spot spraying weeds as far 10.7-m (35-ft) away and trees up to 9.1-m (30-ft) high.

Key features

  • Rate control technology – allows operators to effortlessly hold their application rate without worrying about maintaining exact ground speed.
  • 8.1-cm (3.2-in.) display – provides operators with the ability to select a spray mode (boom or wand), adjustments to the speed range, tip size, and flow rate, and individually activate or deactivate tips for greater application options.
  • Pressure control through return valve – helps maintain the droplet size defined by the spray tip, which is important as some materials require different droplet sizes.
  • Individual tip shutoff – provides greater options for different spraying applications.
  • Shurflo 20-L/min (5.3-gpm) pump – is designed for high-hour commercial applications and provides up to 4.1 bar (60 psi) on demand.
  • Spring-loaded, folding steel boom – applies up to 3.8-m (12.5-ft) spray swath. Five XRC TeeJet® nozzles are used to prevent dripping that can lead to spotting.
  • Adjustable hand wand – features a brass tip with a spray pattern that can be adjusted from cone to stream, perfect for spraying trees, weeds, and hard-to-reach places.

Compatibility

  • Model year 2018 and newer Gator XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Full-Size Crossover Utility Vehicles

Specifications

 

Tank

Material

Blow-molded yellow polyethylene plastic

Lid

12.7-cm (5-in.) plastic screw-on breathable lid with tether

Fill-level indication

Molded on tank (in gallons)

Recirculation

Yes - through tank

Sump

Yes - molded in bottom of tank

Drain

No drain

Pump

Type

Shurflo on-demand diaphragm-type pump

Pressure

0 to 4.1 bar (0 to 60 psi) – adjustable through recirculation

Flow rate

20 L/min (5.3 gpm)

Electrical

18 amps max

Boom

Material

Powder-coated steel

Type

Manually-folded, spring-loaded breakaway boom

Nozzles

XRC TeeJet nozzles with check valve screens

–Folded width

1.5 m (5 ft)

–Unfolded width

3 m (10 ft)

Spray width

3.8 m (12.5 ft)

Hand wand

Material

Polypropylene with Viton® rubber seals

Tip

Brass - adjustable (mist, cone, stream)

Hose diameter

1.3 cm (1/2 in.)

Hose length

9.1 m (30 ft)

Vertical spray distribution

9.1 m (30 ft)

Horizontal spray distribution

10.7 m (35 ft)

Frame

Material

Powder-coated steel

Capacities

Tank capacity

341 L (90 gal.)

Weight - tank empty

65 kg (143 lb)

Weight - tank full

380 kg (839 lb)

Warranty

Residential

2 years

Commercial

6 months

Components included

  • 341-L (90-gal.) sprayer assembly
  • 3.8-m (12.5-ft) boom and support components
  • 9.1-m (30-ft) deluxe hand wand
  • Controller and mounting plate
  • 8.1-cm (3.2-in.) display
  • Display mounting bracket
  • Dash, chassis, and sprayer harnesses
  • Hardware
  • Operator's manual

Required John Deere parts

  • E-Spec Full-Size Crossover Gator Utility Vehicles (XUV835E and XUV865E)
    • Dash port attachment harness (BM26268)
    • E-Spec attachment harness (BM26266)
    • CAN bridge (BUC10316)
  • M-Spec Full-Size Crossover Gator Utility Vehicles (XUV835M and XUV865M)
    • Dash port attachment harness (BM26268)
    • CAN bridge (BUC10316)
  • R-Spec Full-Size Crossover Gator Utility Vehicles (XUV835R and XUV865R)
    • Dash port attachment harness (BM26268)
    • CAN bridge (BUC10316)
  • Shurflo is a trademark of Pentair Flow Technologies, LLC. TeeJee is a trademark of Spraying Systems Co. Viton is a trademark of The Chemours Company FC, LLC.
Sprayer wiring kit components Sprayer wiring kit components
Overview

This sprayer wiring kit provides plug-and-go functionality for customers with Full-Size Crossover Gator Utility Vehicles with deluxe cargo boxes and compatible sprayers. Instead of connecting a sprayer's wiring directly to the battery, this kit utilizes the vehicle's pre-installed wiring for a cleaner initial installation and simplified routine attachment afterwards.

Benefits
  • Plug-and-go compatibility utilizing the vehicle's pre-installed wiring instead of connecting directly to the battery
  • Convenient dash-mounted switch puts on/off control of a sprayer within short reach
Additional details

Included with each kit are four harnesses. Two (the upper and lower harnesses) are for the on/off rocker switch, which can be installed in one of the blank switch plates on the vehicle's dash. The chassis harness runs along the rear of the chassis, extending power and data ports to the back corner of the vehicle. Lastly, the sprayer harness connects to the chassis harness and runs to the sprayer pump, providing a clean and tidy wiring solution.

Compatibility

  • Model year 2018 and newer Gator XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Full-Size Crossover Utility Vehicles
  • Sprayers:
    • LP33597 – 94.6-L (25-gal.) sprayer for Gator utility vehicles
    • LP20852 – 170.3-L (45-gal.) sprayer for Gator utility vehicles
    • LP22908 – 170.3-L (45-gal.) deluxe sprayer for Gator utility vehicles
    • LP48006 – 341-L (90-gal.) deluxe sprayer for Gator utility vehicles
    • LP20853 – 341-L (90-gal.) dual-tank sprayer for Gator utility vehicles
    • LP22909 – 341-L (90-gal.) deluxe dual-tank sprayer for Gator utility vehicles

Components included

  • Upper dash harness
  • Lower dash harness
  • Rocker switch (on/off)
  • Rocker switch sticker
  • Chassis harness
  • Sprayer harness
  • Hardware (includes zip ties and wire harness clips)
  • Installation instructions

Required John Deere parts

  • E-Spec Full-Size Gator Utility Vehicles (XUV835E and XUV865E)
    • Dash port attachment harness (BM26268)
    • E-Spec attachment harness (BM26266)
  • M-Spec Full-Size Gator Utility Vehicles (XUV835M and XUV865M)
    • Dash port attachment harness (BM26268)
  • R-Spec Full-Size Gator Utility Vehicles (XUV835R and XUV865R)
    • Dash port attachment harness (BM26268)

Spreaders

0.3-m3 (10-cu ft) in-bed spreader for XUV835 and XUV865 0.3-m3 (10-cu ft) in-bed spreader for XUV835 and XUV865
Overview

The 0.3-m3 (10-cu ft) in-bed spreader easily expands the capabilities and productivity of operators with Gator XUV835 and XUV865 Full-Size Crossover Utility Vehicles. Featuring exclusive controls and ample hopper capacity, these spreaders are the ideal spreading solution to help operators quickly apply large amounts of ice melt materials.

Benefits
  • Easily control the mounted spreader with the 9-cm (3.5-in.) weatherproof, color display. Four push buttons are used to navigate functions including independent adjustment of the auger and spinner speeds, vibratory motor settings, auger reverse to clear out jammed material, and unload mode to completely empty the hopper. The display easily mounts to the vehicle's dash by utilizing existing holes.
    • If a controller area network (CAN) bridge (BUC10316) is installed on the utility vehicle, operators can access automatic stop, which halts spreader operation when the vehicle stops moving.
  • Enjoy long periods of spreading ice melt materials with the ample volume of the 0.3-m3 (10-cu ft) poly hopper.
  • The 7.6-cm (3-in.) diameter steel auger is powered by a direct-drive motor and features variable speed control, automatic jam clearing, and reverse to clear jammed material.
  • Quickly cover large areas up to 9.1-m (30-ft) wide using the 30.5-cm (12-in.) diameter steel spinner with independent speed control.
    • This entire assembly can be quickly disconnected to access the vehicle's hitch and reduce the spreader's overall footprint for storage.
  • Eliminate bridged material inside the hopper with the vibratory motor that features four modes (pulse, low, high, and ramp).
  • A top screen and fitted tarp are included to help with material handling. The top screen prevents clumped material from entering the hopper, while the fitted tarp helps keep material dry.
  • Get a dedicated, secure fit to the cargo box from the provided mounting hardware. Two stainless-steel tie-down rods secure the spreader to the tie-down hooks in the bed.
Additional details

The 0.3-m3 (10-cu ft) in-bed spread is compatible with model year 2018 and newer XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Utility Vehicles.

Specifications 
Measurements 
Length - overall 183 cm (72 in.)
Length - spinner removed 154 cm (60.5 in.)
Width 123.2 cm (48.5 in.)
Height - bottom of spinner to top of hopper 105 cm (41.4 in.)
Height - bottom of spreader to top of hopper 67 cm (26.4 in.)
Auger diameter 7.6 cm (3 in.)
Spinner diameter 30.5 cm (12 in.)
Capacities
Hopper volume - filled to top screen 0.3 m3 (10 cu ft)
Spreader weight - hopper empty 138 kg (305 lb)
Spreader weight - hopper full Varies by material – consult the operator's manual for weight limits
Materials
Hopper Single-piece polyethylene
Spinner and frame Powder-coated steel
Top screen 7.9-mm (5/16-in.) powder-coated steel rod
Motors - auger, spinner, vibrator 12-V, semi-sealed
Operation
Maximum spreading width 9.1 m (30 ft)
Display functions
  • On/off
  • Spinner speed
  • Auger speed
  • Auger reverse
  • Auto jam clearing
  • Unload mode
  • Vibrator mode (low, high, ramp, pulse)
  • Diagnostic information
  • Auto stop (CAN Bridge required)
Warranty
Residential 1 year
Commercial 6 months

 

17AT Cart 17AT Cart
  • 0.5-m 3 (17-cu ft) capacity
  • 453.6-kg (1000-lb) load limit
  • Copolymer polypropylene is compression molded for optimum thickness in all areas and maximum durability
  • Heavy-duty, reinforced structural frame with a 25.4-mm (1-in.) diameter, one-piece axle to handle weight, speed, and bumps
  • Spring-loaded dump latch for easy dumping and positive lock to prevent accidental unlocking when being towed
  • Double-sealed, high-speed roller bearings to handle a 48-km/h (30-mph) maximum speed
  • Heavy-duty polyethylene bed
    • Accepts dividers to separate cargo (template included)
  • All-terrain knobby tires
    • Provides good flotation and traction in mud, sand, and other wet or soft areas
    • Flexes over bumps and ruts for a smoother, more controlled ride
    • Minimizes ground compaction to save turf and prevent ruts in soft ground
  • Poly fenders to keep the operator, cart, and vehicle clean
  • Suitable for use with most John Deere utility vehicles equipped with a 48-mm (1.875-in.) ball hitch, including Gator™ Utility Vehicle models TX, TX Turf, TH 6x4, TH 6x4 Diesel, all HPX 4x4 models, and all XUV models
  • Quality and styling compatible with other John Deere equipment
Ordering information

Contact your local John Deere dealer for availability and pricing information.

 

17AT Cart

Order number: LPPCT17ATJD

0.14-m3 (5-cu ft) drop spreader 0.14-m3 (5-cu ft) drop spreader
Overview

Whether it's a snow removal contractor, a grounds crew at a college campus, or a municipality working downtown, a drop spreader is a professional's choice for precision spreading. This drop spreader combines a large, 0.14-m3 (5-cu ft) material capacity with a precise 109-cm (43-in.) spread width that's ideal for salting sidewalks. Heavy-gauge stainless-steel construction, simple drives, and an industry-exclusive removable rotor tray make this attachment the ultimate spreading solution.

Benefits
  • Enjoy long periods of spreading with the stainless-steel hopper that offers 0.14-m3 (5-cu ft) of material capacity.
  • The stainless-steel rotor is segmented to enhance the accuracy of material distribution with the 109-cm (43-in.) spread width.
  • Simple, enclosed drives help enhance the spreader's longevity.
  • Get perfect, tool-free selection of material flow with a six-position gate.
  • Experience an easy, tool-free cleanout from the industry-exclusive removable rotary tray.
  • Eliminate material bridging with the vibration motor.
  • Enhance productivity with the multipurpose use of the spreaderUse it in the winter to spread ice-melt material and in the summer to apply fertilizer, topsoil, and lime.
Additional details

The 0.14-m3 (5-cu ft) drop spreader is compatible with model year 2018 and newer XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Utility Vehicles.

To adapt this spreader to a XUV835 or XUV865 Utility Vehicle, the XUV835/XUV865 hitch and display (LP69908) is required.

Specifications:
  • Hopper capacity: 159 kg (350 lb), varies by material
  • Rotor speed: 1.3 to 6 rpm
  • Electrical: 12 V
0.085-m3 (3-cu ft) fertilizer spreader 0.085-m3 (3-cu ft) fertilizer spreader
Overview

The 0.085-m3 (3-cu ft) fertilizer spreader for Gator XUV835 and XUV865 Full-Size Crossover Utility Vehicles is ideal for applying fertilizer, seed, herbicide, and other fine-particle materials. This spreader features a poly hopper with up to 109 kg (240 lb) of material capacity to minimize refilling. After pairing with a Gator hitch and display (LP69908), spread-width adjustments can be made up to 6.1 m (20 ft).

Benefits
  • Enjoy long periods of spreading with a poly hopper that offers 109 kg (240 lb) of material capacity.
  • Get long-term durability from the stainless-steel, 25.4-cm (10-in.) diameter spinner.
  • Control the flow of fine materials through the adjustable gate operated with an electric actuator.
  • Control the spread pattern with the side deflector.
  • Satisfy heavy-duty spreading demands using the 1/4-kW (1/3-hp), semi-sealed electric motor.
  • Improve durability in rugged conditions with a powder-coated steel frame.
Additional details

The 0.085-m3 (3-cu ft) fertilizer spreader is compatible with model year 2018 and newer XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Utility Vehicles.

To adapt this fertilizer spreader to an XUV835 or XUV865 Utility Vehicle, the XUV835/XUV865 hitch and display (LP69908) is required.

0.085-m3 (3-cu ft) salt spreader 0.085-m3 (3-cu ft) salt spreader
Overview

The 0.085-m3 (3-cu ft) salt spreader for Gator XUV835 and XUV865 Full-Size Crossover Utility Vehicles is the convenient spreading solution for applying rock salt in winter weather. This spreader features a poly hopper with up to 109 kg (240 lb) of material-carrying capacity. After pairing with a Gator hitch and display (LP69908), spread-width adjustments can be made up to 7.6 m (25 ft) wide.

Benefits
  • Enjoy long periods of spreading with the poly hopper that offers 109 kg (240 lb) of material capacity.
  • Easily move large-particle material, like rock salt, to the spinner with the vertical auger.
    • NOTE: The spreader is not well suited to handle fine-particle materials like calcium chloride.
  • The 25.4-cm (10-in.) diameter, nylon, glass-reinforced spinner withstands corrosive ice melt products for long-term use.
  • Satisfy heavy-duty spreading demands with the 1/4-kW (1/3-hp), semi-sealed electric motor.
  • Improve durability in rugged conditions with a powder-coated steel frame.
Additional details

The 0.085-m3 (3-cu ft) salt spreader is compatible with model year 2018 and newer XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Utility Vehicles.

To adapt this salt spreader to an XUV835 or XUV865 Utility Vehicle, the XUV835/XUV865 hitch and display (LP69908) is required.

Hitch and display for XUV835 and XUV865 Hitch and display for XUV835 and XUV865
Overview

The hitch and display for Gator XUV835 and XUV865 Full-Size Crossover Utility Vehicles are specifically designed to work with a 0.085-m3 (3-cu ft) salt spreader (LP69909), a 0.085-m3 (3-cu ft) fertilizer spreader (LP69910), or a 0.14-m3 (5-cu ft) drop spreader (LP69911).

Each hitch features a spring-loaded mechanism to allow for quick spreader attachment and removal. The hitch can also be lowered to provide easy access for routine service.

This latest generation of utility vehicles offer greater electronic capabilities than ever before. As a result, operators have access to enhanced functionality and controls, which is seen through the 9-cm (3.5-in.) weatherproof, color display.

Benefits
  • Easily control the mounted spreader with the 9-cm (3.5-in.) weatherproof color display. Four push buttons are used to navigate functions including independent adjustment of the auger and spinner speeds and activating the vibratory motor on 0.14-m3 (5-cu ft) drop spreaders. The display mounts easily to the vehicle's dash by utilizing existing holes.
    • If a controller area network (CAN) bridge (BUC10316) is installed on the Gator, operators will also have access to automatic stop functionality, where spreader operation halts when the vehicle stops.
  • Designed specifically for Gator utility vehicles, the hitch ensures safe and secure spreader fitment.
  • The powder-coated steel hitch provides the utmost support and durability.
Additional details

The hitch and display are compatible with the following models:

  • Model year 2018 and newer XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R
  • 0.085-m3 (3-cu ft) salt spreader (LP69909)
  • 0.085-m3 (3-cu ft) fertilizer spreader (LP69910)
  • 0.14-m3 (5-cu ft) drop spreader (LP69911)

Storage

Label kit for toolboxes (Green & Yellow) - 57KAMBM26220

MOLLE large storage pouch - black MOLLE large storage pouch - black
MOLLE large storage pouch - camo MOLLE large storage pouch - camo
MOLLE large storage pouch - brown MOLLE large storage pouch - brown

NOTE: Available through OrderZone.

 

The large MOLLE storage pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

 

Special features:

  • Dual military-grade zippers and pulls
  • Constructed with military-grade CORDURA® fabrics
  • Utilizes the MOLLE attachment system
  • Pair of 127-mm (5-in.) MOLLE sticks included
  • Available in black, brown, or Realtree Hardwoods HD® camo pattern
  • Inner liner made of high-density coated pack-cloth nylon fabric
  • Built-in drain hole
  • Limited 1-year warranty
  • Made in the USA

 

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE device pouch MOLLE device pouch

Available through OrderZone

 

Compatible with bench seat covers and operator protection system (OPS) MOLLE storage panel

 

Special features:

  • Velcro flap closure
  • Padded to protect device and contents
  • Constructed with military-grade Cordura™ fabrics
  • Utilizes the MOLLE attachment system
  • Pair of 6-in. (152.4-mm) MOLLE sticks included
  • Available in black or REALTREE HARDWOODS HD™ pattern
  • Inner liner made of high-density coated pack-cloth nylon fabric
  • Built-in drain hole
  • Limited 1-year warranty
  • Made In U.S.A.

 

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

MOLLE device pouch MOLLE device pouch

Available through OrderZone

 

Compatible with bench seat covers and operator protection system (OPS) MOLLE storage panel

 

Special features:

  • Velcro flap closure
  • Padded to protect device and contents
  • Constructed with military-grade Cordura™ fabrics
  • Utilizes the MOLLE attachment system
  • Pair of 6-in. (152.4-mm) MOLLE sticks included
  • Available in black or REALTREE HARDWOODS HD™ pattern
  • Inner liner made of high-density coated pack-cloth nylon fabric
  • Built-in drain hole
  • Limited 1-year warranty
  • Made In U.S.A.

 

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

MOLLE fire extinguisher pouch - black MOLLE fire extinguisher pouch - black
MOLLE fire extinguisher pouch - camo MOLLE fire extinguisher pouch - camo
MOLLE fire extinguisher pouch - coyote brown MOLLE fire extinguisher pouch - coyote brown

NOTE: Available through OrderZone.

 

The MOLLE fire extinguisher pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

 

Special features:

  • Military-grade rapid extraction clips
  • Fits standard round 1.1-kg (2.5-lb) fire extinguishers
  • Padded to protect contents
  • Constructed with military-grade CORDURA® fabrics
  • Utilizes the MOLLE attachment system
  • Pair of 15.2-cm (6-in.) MOLLE sticks included
  • Available in black, coyote brown, or Realtree Hardwoods HD® camo pattern
  • Inner liner made of high-density coated pack-cloth nylon fabric
  • Limited 1-year warranty
  • Made in the USA

 

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE fire extinguisher pouch - black MOLLE fire extinguisher pouch - black
MOLLE fire extinguisher pouch - camo MOLLE fire extinguisher pouch - camo
MOLLE fire extinguisher pouch - coyote brown MOLLE fire extinguisher pouch - coyote brown

NOTE: Available through OrderZone.

 

The MOLLE fire extinguisher pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

 

Special features:

  • Military-grade rapid extraction clips
  • Fits standard round 1.1-kg (2.5-lb) fire extinguishers
  • Padded to protect contents
  • Constructed with military-grade CORDURA® fabrics
  • Utilizes the MOLLE attachment system
  • Pair of 15.2-cm (6-in.) MOLLE sticks included
  • Available in black, coyote brown, or Realtree Hardwoods HD® camo pattern
  • Inner liner made of high-density coated pack-cloth nylon fabric
  • Limited 1-year warranty
  • Made in the USA

 

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE large storage pouch - black MOLLE large storage pouch - black
MOLLE large storage pouch - camo MOLLE large storage pouch - camo
MOLLE large storage pouch - brown MOLLE large storage pouch - brown

NOTE: Available through OrderZone.

 

The large MOLLE storage pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

 

Special features:

  • Dual military-grade zippers and pulls
  • Constructed with military-grade CORDURA® fabrics
  • Utilizes the MOLLE attachment system
  • Pair of 127-mm (5-in.) MOLLE sticks included
  • Available in black, brown, or Realtree Hardwoods HD® camo pattern
  • Inner liner made of high-density coated pack-cloth nylon fabric
  • Built-in drain hole
  • Limited 1-year warranty
  • Made in the USA

 

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE large storage pouch - black MOLLE large storage pouch - black
MOLLE large storage pouch - camo MOLLE large storage pouch - camo
MOLLE large storage pouch - brown MOLLE large storage pouch - brown

NOTE: Available through OrderZone.

 

The large MOLLE storage pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

 

Special features:

  • Dual military-grade zippers and pulls
  • Constructed with military-grade CORDURA® fabrics
  • Utilizes the MOLLE attachment system
  • Pair of 127-mm (5-in.) MOLLE sticks included
  • Available in black, brown, or Realtree Hardwoods HD® camo pattern
  • Inner liner made of high-density coated pack-cloth nylon fabric
  • Built-in drain hole
  • Limited 1-year warranty
  • Made in the USA

 

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE small storage pouch - black MOLLE small storage pouch - black
MOLLE small storage pouch - camo MOLLE small storage pouch - camo
MOLLE small storage pouch - brown MOLLE small storage pouch - brown

NOTE: Available through OrderZone.

 

The small MOLLE storage pouches are compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

 

Special features:

  • Military-grade zippers and pulls
  • Constructed with military-grade CORDURA® fabrics
  • Utilizes the MOLLE attachment system
  • Pair of 127-mm (5-in.) MOLLE sticks included
  • Available in black, brown, or Realtree Hardwoods HD® camo pattern
  • Inner liner made of high-density coated pack-cloth nylon fabric
  • Limited 1-year warranty
  • Made in the USA

 

Cordura is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE small storage pouch - black MOLLE small storage pouch - black
MOLLE small storage pouch - camo MOLLE small storage pouch - camo
MOLLE small storage pouch - brown MOLLE small storage pouch - brown

NOTE: Available through OrderZone.

 

The small MOLLE storage pouches are compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

 

Special features:

  • Military-grade zippers and pulls
  • Constructed with military-grade CORDURA® fabrics
  • Utilizes the MOLLE attachment system
  • Pair of 127-mm (5-in.) MOLLE sticks included
  • Available in black, brown, or Realtree Hardwoods HD® camo pattern
  • Inner liner made of high-density coated pack-cloth nylon fabric
  • Limited 1-year warranty
  • Made in the USA

 

Cordura is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

Water bottle pouch with three color options Water bottle pouch with three color options
Overview

This water bottle pouch attaches to the backrest of utility vehicle seat covers that use the military-inspired modular lightweight load-carrying equipment (MOLLE) attachment system. The pouch fits up to a 0.95-L (32-oz) wide-mouth bottle.

Benefits
  • Military-grade zipper and pull
  • Constructed with military-grade CORDURA® fabrics
  • Easily attaches with built-in straps
  • Customizable with three colors: black, coyote brown, and Realtree EDGE™ camo
  • Durable inner liner made of high-density coated pack cloth nylon fabric
Additional details
  • Dimensions – 22.9 cm (9 in.) high, 10.2 cm (4 in.) wide, and 10.2 cm (4 in.) long
  • Limited 1-year warranty
  • Made in the USA

CORDURA is a trademark of INVISTA North America S.a.r.l. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE fire extinguisher pouch - black MOLLE fire extinguisher pouch - black
MOLLE fire extinguisher pouch - camo MOLLE fire extinguisher pouch - camo
MOLLE fire extinguisher pouch - coyote brown MOLLE fire extinguisher pouch - coyote brown

NOTE: Available through OrderZone.

 

The MOLLE fire extinguisher pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

 

Special features:

  • Military-grade rapid extraction clips
  • Fits standard round 1.1-kg (2.5-lb) fire extinguishers
  • Padded to protect contents
  • Constructed with military-grade CORDURA® fabrics
  • Utilizes the MOLLE attachment system
  • Pair of 15.2-cm (6-in.) MOLLE sticks included
  • Available in black, coyote brown, or Realtree Hardwoods HD® camo pattern
  • Inner liner made of high-density coated pack-cloth nylon fabric
  • Limited 1-year warranty
  • Made in the USA

 

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

Water bottle pouch with three color options Water bottle pouch with three color options
Overview

This water bottle pouch attaches to the backrest of utility vehicle seat covers that use the military-inspired modular lightweight load-carrying equipment (MOLLE) attachment system. The pouch fits up to a 0.95-L (32-oz) wide-mouth bottle.

Benefits
  • Military-grade zipper and pull
  • Constructed with military-grade CORDURA® fabrics
  • Easily attaches with built-in straps
  • Customizable with three colors: black, coyote brown, and Realtree EDGE™ camo
  • Durable inner liner made of high-density coated pack cloth nylon fabric
Additional details
  • Dimensions – 22.9 cm (9 in.) high, 10.2 cm (4 in.) wide, and 10.2 cm (4 in.) long
  • Limited 1-year warranty
  • Made in the USA

CORDURA is a trademark of INVISTA North America S.a.r.l. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

Water bottle pouch with three color options Water bottle pouch with three color options
Overview

This water bottle pouch attaches to the backrest of utility vehicle seat covers that use the military-inspired modular lightweight load-carrying equipment (MOLLE) attachment system. The pouch fits up to a 0.95-L (32-oz) wide-mouth bottle.

Benefits
  • Military-grade zipper and pull
  • Constructed with military-grade CORDURA® fabrics
  • Easily attaches with built-in straps
  • Customizable with three colors: black, coyote brown, and Realtree EDGE™ camo
  • Durable inner liner made of high-density coated pack cloth nylon fabric
Additional details
  • Dimensions – 22.9 cm (9 in.) high, 10.2 cm (4 in.) wide, and 10.2 cm (4 in.) long
  • Limited 1-year warranty
  • Made in the USA

CORDURA is a trademark of INVISTA North America S.a.r.l. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

Rapid recovery rope kit Rapid recovery rope kit

Available through OrderZone

 

Special features:

  • Extreme off-road kinetic recovery rope and storage bag
  • Rope measures 9/16 in. (21 mm) X 20 ft (6.1 m) and is constructed of double-braided nylon
  • 5,000-lb (2268-kg) tensile strength
  • Bag is constructed with military-grade Cordura™ fabrics with built-in carry handle
  • Bag utilizes the modular lightweight load-carrying equipment (MOLLE) attachment system with two 6–in. (152.7-mm) MOLLE sticks included
  • Bag available in black or REALTREE HARDWOODS HD™ pattern
  • Limited 1-year warranty
  • Made In U.S.A.

 

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

Rapid recovery rope kit Rapid recovery rope kit

Available through OrderZone

 

Special features:

  • Extreme off-road kinetic recovery rope and storage bag
  • Rope measures 9/16 in. (21 mm) X 20 ft (6.1 m) and is constructed of double-braided nylon
  • 5,000-lb (2268-kg) tensile strength
  • Bag is constructed with military-grade Cordura™ fabrics with built-in carry handle
  • Bag utilizes the modular lightweight load-carrying equipment (MOLLE) attachment system with two 6–in. (152.4-mm) MOLLE sticks included
  • Bag available in black or REALTREE HARDWOODS HD™ pattern
  • Limited 1-year warranty
  • Made In U.S.A.

 

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

Side-door opening toolbox Side-door opening toolbox

This custom toolbox was specifically designed for users desiring more integrated sealed storage in a cargo box.

 

Side-door opening toolbox features:

  • 125-L (4.4-cu ft) sealed storage
  • Heavy-gauge sheet metal
  • D-rings for tie downs
  • Fully sealed lockable latch
  • Sealed door
  • Door can also be used as a work bench when down
  • Can be mounted on either side of the cargo box

Weight

29 kg (64 lb)

Capacity

34 kg (75 lb)

Dimensions

Full box: 109.4-cm (43.1-in.) long, 35-cm (13.8–in.) wide, and 32.5-cm (12.8–in.) tall

The toolbox can be installed in minutes by simply removing the cargo box sides and tailgate and bolting the toolbox onto the cargo box.

 

The toolbox requires the tailgate with brake and tail lights kit (BUC10393) and optional label kit:

  • BM26220 – green and yellow

This toolbox is compatible with the following Gator™ Utility Vehicle models:

  • TX
  • TX Turf
  • TE
  • TH
  • XUV625i
  • XUV825i/E/M
  • XUV825i/E/M S4
  • XUV855D/E/M
  • XUV855D/E/M S4
  • XUV835E/M/R
  • XUV865E/M/R
  • Model year 2018 and newer HPX615 and HPX815
MOLLE small storage pouch - black MOLLE small storage pouch - black
MOLLE small storage pouch - camo MOLLE small storage pouch - camo
MOLLE small storage pouch - brown MOLLE small storage pouch - brown

NOTE: Available through OrderZone.

 

The small MOLLE storage pouches are compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

 

Special features:

  • Military-grade zippers and pulls
  • Constructed with military-grade CORDURA® fabrics
  • Utilizes the MOLLE attachment system
  • Pair of 127-mm (5-in.) MOLLE sticks included
  • Available in black, brown, or Realtree Hardwoods HD® camo pattern
  • Inner liner made of high-density coated pack-cloth nylon fabric
  • Limited 1-year warranty
  • Made in the USA

 

Cordura is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

Tailgate with brake lights and taillights Tailgate with brake lights and taillights

This tailgate kit with brake lights and taillights is specifically designed for compatibility with the top and side-door toolboxes (BM26162 and BM26160).

 

The tailgate can be installed in minutes once the toolbox and tail lights are installed by bolting them to the tailgate bracket.

 

Optional label kits are designed to fit with this tailgate:

  • BM26220 – green and yellow

The tailgate is compatible with the following Gator™ utility vehicle models:

  • TX
  • TX Turf
  • TE
  • TH
  • XUV625i
  • XUV825i/E/M
  • XUV825i/E/M S4
  • XUV855D/E/M
  • XUV855D/E/M S4
  • XUV835E/M/R
  • XUV865E/M/R
  • Model Year 2018 - current HPX615 and HPX815
Top-door opening toolbox Top-door opening toolbox

This custom toolbox was specifically designed for users desiring more integrated sealed storage in a cargo box.

 

Top door opening toolbox features:

  • 125-L (33-gal.) sealed storage
  • Heavy-gauge sheet metal
  • D-rings for tie downs
  • Fully sealed lockable latch
  • Sealed door
  • Toolbox divider
  • Removable tool tray
  • Can be mounted on either side of the cargo box

 

Top door opening toolbox

Toolbox weight

32.7 kg (72 lb)

Toolbox capacity

32.7 kg (75 lb)

Toolbox dimensions

-Tray: 27.4-cm (10.8-in.) long x 21.8-cm (8.6-in.) wide x 7.1-cm (2.8–in.) deep -Left-hand side compartment: 46.2-cm (18.2–in.) long X 32.5-cm (12.8–in.) wide X 35.3-cm (13.9–in.) tall -Right-hand side compartment: 62.7-cm (24.7–in.) long X 32.5-cm (12.8–in.) wide X 35.3-cm (13.9-in.) tall

-125-L (33-gal.) total volume

The toolbox can be installed in minutes by simply removing the cargo box sides and tailgate, and bolting the toolbox onto the cargo box.

 

The toolbox requires the tailgate with brake and tail lights kit BUC10393 and optional label kit:

  • BM26220 – green and yellow

This toolbox is compatible with the following Gator™ Utility Vehicle models:

  • TX
  • TX Turf
  • TE
  • TH
  • XUV625i
  • XUV825i/E/M
  • XUV825i/E/M S4
  • XUV855D/E/M
  • XUV855D/E/M S4
  • XUV835E/M/R
  • XUV865E/M/R
  • Model year 2018 and newer HPX615 and HPX815

Tracks

Tracks Tracks
Overview

Wheeled utility vehicles get buried very quickly in deep snow, swamps, sand, or muddy ground conditions. Adding a Camso tracks system takes you where wheels simply cannot go.

Benefits
  • Improves flotation and traction
  • All season capability – ideal for snow, mud, and marsh
  • Easily switch between tracks and wheels
Additional details
  • Compatible with model year 2021 and newer XUV835 and XUV865 Utility Vehicles

Camso is a trademark of Artic Investments S. A.

Turn Signals

Front turn signals Front turn signals
Rear signal lights (taillight protectors not included) Rear signal lights (taillight protectors not included)
Hazards switch (top) Hazards switch (top)
Turn signal switch (right) Turn signal switch (right)
Key features
  • Kit includes:
    • Front/rear turn signals
    • Hazards
    • Backlit switches

NOTE: Not intended for use on public roadways.

Compatibility
  • Compatible with all model year 2011 to current Gator™ XUV825 and XUV825 S4 Utility Vehicles
    • Also requires turn signal light harness kit
  • Compatible with all model year 2011 to current Gator XUV625i, XUV855, and XUV855 S4 Utility Vehicles
    • Also requires turn signal light harness kit
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Electrical harness requirements
XUV835/865  Attachment harness required (see below) 
 M (open station)  2
 M (cab, factory installed)  2
 R  ---

 

E-spec attachment harness 
2 Front attachment harness
Roof attachments harness
Front cab harness 
Rear cab harness 
Dash port harness 

Winch

Winch accessories kit Winch accessories kit

Double the pulling power, change the pulling direction, and keep the winch in proper working order.

The accessories kit is essential gear for operators getting the most out of their winch:

  • Effectively anchors to trees/boulders
  • Change the pulling direction
  • Double the pulling capacity

The accessories kit includes:

  • Flexible tree strap
  • Snatch block
  • Shackle

Each kit comes in a black Cordura® heavyweight-nylon soft case.

 

Cordura is a trademark of INVISTA.

2041-kg (4500-lb) winch (chassis mounted) 2041-kg (4500-lb) winch (chassis mounted)
Plug-in remote Plug-in remote
Key features
  • Impressive pulling capacity of 2041 kg (4500-lb)
  • Equipped with a water-resistant contactor that supplies the amperage required for higher pulling capacities
  • Includes a 3.05-m (10-ft), water-resistant, plug-in remote for safe distance operation that plugs directly into the glove box
  • 15.2 m (50 ft) of 5.6-mm (7/32-in.) synthetic rope with hawse fairlead
    • Synthetic rope does not develop sharp burrs like steel rope and does not store as much potential energy when under load
  • Ergonomic clutch handle
  • Limited lifetime, 3-year electrical (North America) warranty offered through WARN
Compatibility
  • Model year 2018 and newer XUV835 and XUV865 Utility Vehicles
  • M-spec and R-spec vehicles come from the factory winch ready, and no additional attachment harnesses are required
  • Requires winch mounting kit to mount the winch either on the chassis or on the front or rear receiver
  • Not compatible with winch mounts BM26252 and BM26393
Electrical harness requirements
XUV835/865  Attachment harness required (see below) 
 E  1

 

E-spec attachment harness
2 Front attachment harness
Roof attachments harness
4 Front cab harness
5 Rear cab harness
6 Dash port harness

WARN is a trademark of WARN Industries, Inc.

Wireless winch remote Wireless winch remote
Wireless winch remote mounted on XUV835 Wireless winch remote mounted on XUV835
Key features
  • Wirelessly control winch from up to 15 m (50 ft) away
  • Weatherproof transmitter has two large buttons, making it easy to operate even while wearing gloves
  • Colored light-emitting diode (LED) lights provide clear operator feedback
  • Kit includes wireless transmitter, receiver, holster, wiring, and mounting hardware
Compatibility
  • Model year 2012 to current XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles
  • Model year 2011 to current XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Winch Mounting Kit

2041-kg (4500-lb) winch (chassis mounted) 2041-kg (4500-lb) winch (chassis mounted)
Key features
  • Kit includes everything needed to mount the winch to the chassis
Compatibility
  • Model year 2018 and newer XUV835 and XUV865 Utility Vehicles
  • Requires WARN VRX 2041-kg (4500-lb) winch (sold separately)

WARN is a trademark of WARN Industries, Inc.

2041-kg (4500-lb) winch (chassis mounted) 2041-kg (4500-lb) winch (chassis mounted)
2041-kg (4500-lb) winch (mounted on rear receiver) 2041-kg (4500-lb) winch (mounted on rear receiver)
Key features
  • Ability to mount the winch on the front or rear receiver
  • Kit includes everything needed to mount the winch to the receiver
Compatibility
  • Model year 2018 and newer XUV835 and XUV865 Utility Vehicles
  • Requires WARN VRX 2041-kg (4500-lb) winch (sold separately)

WARN is a trademark of WARN Industries, Inc.

Windshield

Windshield washer bottle Windshield washer bottle
Backlit three-position switch Backlit three-position switch
Washer bottle location behind access panel Washer bottle location behind access panel
Key features
  • Wash away dirt and debris with a quick flip of a switch
  • Washer bottle conveniently located behind access panel
  • Washer fluid comes out of nozzle on wiper arm (windshield wiper kit required)
  • Kit includes washer bottle, hose connections, and three-position switch
Compatibility
  • Model year 2018 to current XUV835 and XUV865 Utility Vehicles
Electrical harness requirements
XUV835/865  Attachment harness required (see below) 
 E  1, 3, 4
 M (open station)  3, 4
 M (cab, factory installed)  ---
 R  ---

 

E-spec attachment harness 
2 Front attachment harness
Roof attachments harness
Front cab harness 
Rear cab harness 
Dash port harness